02-22-2021 12:45 PM
Hi
we working on Network Video Surveillance project, the DiVAR and cameras and workstation should be connected to switch to functioning , we power on the C9300 16.12 Gibralter and we did the day0 configuration and we create vlan and everything is okay, today i cannot connect to management port of the switch the pc ethernet card cant recognize the management port even thou the management port green led is active.
any help will be highly appreciated, this is my first time i touch a switch
thank you
Solved! Go to Solution.
02-22-2021 08:15 PM
if you have configured correctly. - if the switch is offering DHCP for you
get progam call putty (google help you)
check your default gateway IP (type ipconfig /all)
use putty to ssh to gateway IP address - you will be asked username/password. (after that enable .password)
# show run (post complete outpput)
or try https://gatewayip ( what you find above step (ip address will be x.x.x.x)
i will also advise spend some time on quick start guide :
02-27-2021 09:04 AM
You should be - what is the challenges here?
02-22-2021 12:53 PM
post the configuration of the device.
02-22-2021 12:58 PM
Hi
i configure the switch by "web ui" and now i cannot connect to switch by management port, and the switch is working when i connect the same cable to any interface and change my pc ip settings it connect fine
02-22-2021 01:08 PM
until we see the configuraiton we do not what you have configured ?
ssh to device and post show run
02-22-2021 01:12 PM
is there another way to configure the switch rather than management port and console port because i don't have console cable.
02-22-2021 01:18 PM
Cat 9300 have 2 ports back-side, make sure you connected right port.
1 is for console
1 is MGMT << you need to connect to this port.
if you able to connect other port and switch working, ssh to switch and post the configuration.
02-22-2021 01:23 PM
yes the switch is working fine, but how to "ssh" on any port! would you please give more details on how to ssh the switch, thank you in advance for your cooporation
02-22-2021 08:15 PM
if you have configured correctly. - if the switch is offering DHCP for you
get progam call putty (google help you)
check your default gateway IP (type ipconfig /all)
use putty to ssh to gateway IP address - you will be asked username/password. (after that enable .password)
# show run (post complete outpput)
or try https://gatewayip ( what you find above step (ip address will be x.x.x.x)
i will also advise spend some time on quick start guide :
02-22-2021 09:51 PM
Thank you balaji
I'll try it
Thanks for support I really appreciate it
02-23-2021 11:17 AM
02-23-2021 02:06 PM
there is no IP given by switch, that is the default ARPA IP address.
As we mentioned, we are not sure what is configured on the switch to suggest best. Get console cable (most of the time come with Switch by default)
refer quick start guide. (spend some time reading the document, the steps are easy )
02-25-2021 11:29 AM
Hello Mr Balaji
at last i made it, now i can connect to this great Gibraltar with Fedora terminal , and this is what we got, is there any way to get back to webui ? i think that the management port is down.
one more question please, we have Network video surveillance, the DiVAR has two NICs working as a team and they are Switch independent, so what should i do on switch side, i think we should make a port channel but what would be the setting of this port channel?
thanks mr balaji, or other guy who like to help
02-25-2021 05:14 PM
Glad to know all went well, happy to help.
02-27-2021 08:57 AM
hello
if i did a factory reset to the switch could i get back to web ui and configure the switch from web browser?
02-27-2021 09:04 AM
You should be - what is the challenges here?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide