C9300-48 - 25 & 40gig ports

[uppermost]

Why do I see 2x25 & 2x40 gig ports on 9300-48P switch if there is only one NM installed, which is C9300-NM-8X (8x10gig ports)

GigabitEthenet1/1/2 unassigned YES unset down down
GigabitEthernet1/1/3 unassigned YES unset down down
GigabitEthernet1/1/4 unassigned YES unset down down
Te1/1/1 unassigned YES unset up up
Te1/1/2 unassigned YES unset administratively down down
Te1/1/3 unassigned YES unset administratively down down
Te1/1/4 unassigned YES unset administratively down down
Te1/1/5 unassigned YES unset administratively down down
Te1/1/6 unassigned YES unset administratively down down
Te1/1/7 unassigned YES unset administratively down down
Te1/1/8 unassigned YES unset administratively down down
Fo1/1/1 unassigned YES unset down down
Fo1/1/2 unassigned YES unset down down
TwentyFiveGigE1/1/1 unassigned YES unset down down
TwentyFiveGigE1/1/2 unassigned YES unset down down

Show inventory:

PID: C9300-48P , VID: V03 , SN: FCW2XXXXX

NAME: "Switch 1", DESCR: "C9300-48P"
PID: C9300-48P , VID: V03 , SN: FCW2XXXXX

NAME: "StackPort1/1", DESCR: "StackPort1/1"
PID: STACK-T1-50CM , VID: V01 , SN: MOC2427A0RS

NAME: "StackPort1/2", DESCR: "StackPort1/2"
PID: STACK-T1-50CM , VID: V01 , SN: LCC2131GK8M

NAME: "Switch 1 - Power Supply A", DESCR: "Switch 1 - Power Supply A"
PID: PWR-C1-1100WAC-P , VID: V01 , SN: DCC2430D644

NAME: "Switch 1 - Power Supply B", DESCR: "Switch 1 - Power Supply B"
PID: PWR-C1-1100WAC-P , VID: V01 , SN: DCC2430DGQD

NAME: "Switch 1 FRU Uplink Module 1", DESCR: "8x10G Uplink Module"
PID: C9300-NM-8X , VID: V03 , SN: FCXXXXXXX

NAME: "Te1/1/1", DESCR: "SFP-10GBase-SR"
PID: SFP-10G-SR , VID: V03 , SN: JUR19050J28

I do not see any 25 or 40 gig in the documentation

[Reza Sharifi · Accepted solution]

Hi,

You can only use the 10Gig ports with that module. All the other ones are just place holders in case you insert a different module in that slot.

HTH

[jackyjoy123]

---

@Reza Sharifi wrote:

Hi,

You can only use the 10Gig ports with that module. All the other ones are just place holders in case you insert a different module in that slot. . 

HTH

---

thanks for the awesome information.

[balaji.bandi]

what is the version of code running - since the switch capable of uplink modules can accomidate that capacity anything x/1/X means uplink module - check the modules supported :

https://www.cisco.com/c/en/us/products/collateral/switches/catalyst-9300-series-switches/nb-06-cat9300-ser-data-sheet-cte-en.html