10-06-2012 01:59 AM - edited 03-07-2019 09:18 AM
Router 1 and Switch 1 form HSRP group
can not ping virtual ip of HSRP in switch2
can not see virtual mac address with sh ip arp
https://skydrive.live.com/redir?resid=E0ED7271C68BE47C!212
another thing i discover only using f0/0 and f0/1 of switch2 to connect others can make
both reconignize active and standby
when using f0/0 and f1/0 of switch2, there will be two active, they can not recognize. Why?
After set all ports in whole topology duplex full and speed 100
Switch2#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.16.0.254 0 Incomplete ARPA
Internet 172.16.0.4 - cc00.0d94.0000 ARPA Vlan1
Switch2#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.16.0.4 - cc00.0d94.0000 ARPA Vlan1
Switch2#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 172.16.0.4 - cc00.0d94.0000 ARPA Vlan1
it has appear but then disappear
router1
f0/0
|
f0/0
switch2 f0/1 -- f0/0 switch1
config t
hostname Router1
int f0/0
ip address 172.16.0.2 255.255.0.0
no shutdown
end
config t
int f0/0
speed 100
duplex full
end
config t
hostname Switch1
int f0/0
no switchport
ip address 172.16.0.3 255.255.0.0
no shutdown
end
config t
int f0/0
standby 1 ip 172.16.0.254
standby 1 priority 200
standby 1 preempt
end
config t
ip routing
int f0/0
standby 1 ip 172.16.0.254
end
config t
hostname Switch2
vlan 1
ip address 172.16.0.4 255.255.0.0
no shutdown
end
ping 172.16.0.254
...
sh ip arp
do not have entry of HSRP virtual mac address
Solved! Go to Solution.
10-06-2012 12:16 PM
Hi,
on router1:
int f0/0
ip add 172.16.0.2 255.255.0.0
standby 1 ip 172.16.0.254
standby 1 priority 101
standby 1 preempt
on 3550:
int f0/3
switchport mode access
switchport access vlan 1
int vlan 1
ip address 172.16.0.3 255.255.0.0
standby 1 ip 172.16.0.254
stanndby 1 preempt
on the 2950: just leave default config
Regards.
Alain
Don't forget to rate helpful posts.
10-06-2012 02:16 AM
Hi,
post a diagram here, your link is not working.
Regards.
Alain
Don't forget to rate helpful posts.
10-06-2012 02:49 AM
port number is not the same as in the diagram, however, connection is correct to follow this diagram
Host A is simulated by Switch2
diagram is
10-06-2012 12:16 PM
Hi,
on router1:
int f0/0
ip add 172.16.0.2 255.255.0.0
standby 1 ip 172.16.0.254
standby 1 priority 101
standby 1 preempt
on 3550:
int f0/3
switchport mode access
switchport access vlan 1
int vlan 1
ip address 172.16.0.3 255.255.0.0
standby 1 ip 172.16.0.254
stanndby 1 preempt
on the 2950: just leave default config
Regards.
Alain
Don't forget to rate helpful posts.
10-07-2012 03:24 AM
i use my older script this time success
the difference is just
ip routing
int f0/0
no switchport
should type ip routing first and then no switchport
above script is no switchport first and then ip routing
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide