Buy or Renew
Buy or Renew
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 
cancel
Start a conversation
2058
Views
10
Helpful
29
Replies

Catalyst 6500 series bootflash

Omar2
Level 1
Level 1

ā€Ž07-17-2018 06:51 AM - edited ā€Ž03-08-2019 03:42 PM

Hello Dears 

I have a problem , my core router 6500 when i reload it or power cycle it , it doesn't load the configuration  i saved it loads the ios image that contains no config at all , how can i make it load the image that contain all of the config i saved , another issue i have is that when i try the 
router(config)boot supboot-disk0:ios image
it says that there is no HA to support the boot config 
i need to load the ios image that i want and save all configuration in it and when i reload it , it should load the latest configuration that i saved 

thanks 

Labels:
0 Helpful
29 Replies 29

Diana Karolina Rojas
Cisco Employee
Cisco Employee

ā€Ž07-17-2018 07:10 AM

Hello!

 

Which is the "show bootvar" output? please paste the "show ver" and show bootvar from the device here. 

 

Best Regards,

0 Helpful

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 07:17 AM

Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASE-M), Version 12.2(33)SXH3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 24-Sep-08 07:00 by prod_rel_team

ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)

Router uptime is 3 minutes
Uptime for this control processor is 3 minutes
Time since Router switched to active is 2 minutes
System returned to ROM by power cycle at 21:29:36 UTC Mon Jul 16 2018 (SP by power on)
System image file is "sup-bootdisk:s72033-ipbase-mz.122-33.SXH3a.bin"

cisco WS-C6509 (R7000) processor (revision 3.0) with 983008K/65536K bytes of memory.
Processor board ID SAL09051FEN
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w reset
1 Virtual Ethernet interface
126 Gigabit Ethernet interfaces
24 Ten Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102

0 Helpful

Omar2
Level 1
Level 1
In response to Omar2

ā€Ž07-17-2018 07:20 AM

Router#show bootvar
BOOT variable =
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102

Standby is up
Standby has 1048576K/65536K bytes of memory.

Standby BOOT variable =
Standby CONFIG_FILE variable = sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Standby BOOTLDR variable does not exist
Standby Configuration register is 0x2102

0 Helpful

Diana Karolina Rojas
Cisco Employee
Cisco Employee
In response to Omar2

ā€Ž07-17-2018 07:25 AM

Did you try to set the boot image you want to use this way?

 

boot system disk0:s72033-adventerprise-mz.151-2.SY7.bin

 

Please do not forget to rate useful post.

Best Regards,

0 Helpful

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 07:32 AM

i tried this but it doesn't show disk0

Router(config)#boot system ?
WORD TFTP filename or URL
flash Boot from flash memory
ftp Boot from a server via ftp
mop Boot from a Decnet MOP server
rcp Boot from a server via rcp
tftp Boot from a tftp server

 

and tried this but the output says HA support is not available 

 

Router(config)#boot config sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
%WARNING: HA support is not available to " boot config " command
any ideas ? 
thanks

0 Helpful

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 07:24 AM

Hello Diana 

thanks for your reply , i want to load this image 

sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
and save configurations in it and if i reload the router or power cycle it 
it should load the image i mentioned and all of the configs that i saved .


Best Regards .

0 Helpful

Diana Karolina Rojas
Cisco Employee
Cisco Employee
In response to Omar2

ā€Ž07-17-2018 07:36 AM

Please try this way: boot system flash disk0:s72033-adventerprise-mz.151-2.SY7.bin and paste the show bootvar after that.

 

Best Regards,

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 07:39 AM

Router(config)#boot system flash disk0:s72033-adventerprise-mz.151-2.SY7.bin
Router(config)#exi
Router(config)#exit
Router#
Router#s
00:24:35: %SYS-5-CONFIG_I: Configured from console by consolehow
Router#show va
Router#show bo
Router#show bootva
Router#show bootvar
BOOT variable =
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102

Standby is up
Standby has 1048576K/65536K bytes of memory.

Standby BOOT variable =
Standby CONFIG_FILE variable = sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Standby BOOTLDR variable does not exist
Standby Configuration register is 0x2102


okay now should i copy the running config and reload the router ?
and after that if i saved a list of configurations and reloaded the router how can i be sure that it will be saved 

best regards 

0 Helpful

Diana Karolina Rojas
Cisco Employee
Cisco Employee
In response to Omar2

ā€Ž07-17-2018 07:43 AM

Sorry but I can't see that the Boot variable has been set in the last "show bootvar", so is not recomendable to reload after we can find a way to set this properly. Let me see and I will try to get a better option.

 

Best Regards,

0 Helpful

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 07:45 AM

many thanks diana i'll be waiting 

0 Helpful

Diana Karolina Rojas
Cisco Employee
Cisco Employee
In response to Omar2

ā€Ž07-17-2018 07:59 AM

boot system flash sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin, try this and after send me this outputs:

 

show run | i boot

show boot

 

Best Regards,

0 Helpful

Omar2
Level 1
Level 1
In response to Diana Karolina Rojas

ā€Ž07-17-2018 08:06 AM

Router(config)#$ flash sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Router(config)#do show boot
Router(config)#do show boot | i boot
Standby CONFIG_FILE variable = sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Router(config)#do show boot
BOOT variable =
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102

Standby is up
Standby has 1048576K/65536K bytes of memory.

Standby BOOT variable =
Standby CONFIG_FILE variable = sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Standby BOOTLDR variable does not exist
Standby Configuration register is 0x2102

0 Helpful

Omar2
Level 1
Level 1
In response to Omar2

ā€Ž07-17-2018 08:21 AM

Router#show bootvar
BOOT variable = disk0:s72033-adventerprise-mz.151-2.SY7.bin,1;sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin,12;sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin,1;
CONFIG_FILE variable = sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
BOOTLDR variable =
Configuration register is 0x2102

Standby is up
Standby has 1048576K/65536K bytes of memory.

Standby BOOT variable = disk0:s72033-adventerprise-mz.151-2.SY7.bin,1;sup-bootdisk:sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin,12;sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin,1;
Standby CONFIG_FILE variable = sup-bootdisk:s72033-adventerprise-mz.151-2.SY7.bin
Standby BOOTLDR variable does not exist
Standby Configuration register is 0x2102

0 Helpful

Diana Karolina Rojas
Cisco Employee
Cisco Employee
In response to Omar2

ā€Ž07-17-2018 08:30 AM

This is the right output, yes you can reload the device.

 

Please do not forget to rate useful post.

Best Regards,

Customers Also Viewed These Support Documents
Review Cisco Networking for a $25 gift card