cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1999
Views
0
Helpful
6
Replies

Cisco 3750-X hangs while booting

Abhishek Nanda
Level 1
Level 1

 *Mar 1 00:00:07.658: Read env variable - LICENSE_BOOT_LEVEL =
*Jan 2 00:00:05.821: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c3750x Next reboot level = ipbase and License = ipbase
*Jan 2 00:01:15.472: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack
*Jan 2 00:01:17.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Jan 2 00:01:17.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Jan 2 00:01:19.784: %SMI-5-CLIENT: Smart Install Client feature is enabled. It is recommended to disable the Smart Install feature when it is not actively used. To disable feature execute 'no vstack' in configuration mode
*Jan 2 00:01:24.875: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Jan 2 00:01:32.568: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 inserted
*Jan 2 00:01:32.568: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 2 inserted
*Jan 2 00:01:35.470: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan5, changed state to down
*Jan 2 00:01:35.529: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan25, changed state to down
*Jan 2 00:01:35.529: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan26, changed state to down
*Jan 2 00:01:35.529: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan27, changed state to down
*Jan 2 00:01:35.588: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan28, changed state to down
*Jan 2 00:01:35.588: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan101, changed state to down
*Jan 2 00:01:35.663: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 2 00:01:35.865: %STACKMGR-5-SWITCH_READY: Switch 1 is READY
*Jan 2 00:01:35.865: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
*Jan 2 00:01:35.865: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
*Jan 2 00:01:36.393: %STACKMGR-5-MASTER_READY: Master Switch 1 is READY
*Jan 2 00:01:37.005: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=1: Transceiver has been inserted
*Jan 2 00:01:37.106: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=2: Transceiver has been inserted
*Jan 2 00:01:37.207: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=3: Transceiver has been inserted
*Jan 2 00:01:37.433: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
*Jan 2 00:01:37.500: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Jan 2 00:01:37.685: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22 by prod_rel_team
*Jan 2 00:01:39.891: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to down
*Jan 2 00:01:40.126: %USB_CONSOLE-6-MEDIA_RJ45: Console media-type is RJ45.
*Jan 2 00:01:41.183: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Jan 2 00:01:48.095: %PLATFORM-6-FRULINK_INSERTED: FRULink 10G ST module inserted in Switch 1.
*Jan 2 00:01:48.817: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=17: Transceiver has been inserted
*Jan 2 00:01:49.731: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=16: Transceiver has been inserted
*Jan 2 00:06:03.000: %PHY-5-TRANSCEIVERREMOVED: Slot=1 Port=16: Transceiver has been removed
*Jan 2 00:06:26.874: %PHY-5-TRANSCEIVERREMOVED: Slot=1 Port=17: Transceiver has been removed
*Jan 2 00:07:05.310: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=17: Transceiver has been inserted
*Jan 2 00:07:19.051: %PHY-5-TRANSCEIVERINSERTED: Slot=1 Port=18: Transceiver has been inserted

 

It doesnt respond further

2 Accepted Solutions

Accepted Solutions

Leo Laohoo
Hall of Fame
Hall of Fame
If there are modules attached, remove them and reboot the switch.

View solution in original post

Could you try a different IOS? Try the latest 15.0(2)SE train.
You'll need to force the switch to boot into ROMmon and force the switch to boot the IOS using USB.

View solution in original post

6 Replies 6

Leo Laohoo
Hall of Fame
Hall of Fame
If there are modules attached, remove them and reboot the switch.

No it still hangs in there.

 

*Mar 1 00:00:07.650: Read env variable - LICENSE_BOOT_LEVEL =
*Jan 2 00:00:05.872: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c3750x Next reboot level = ipbase and License = ipbase
*Jan 2 00:01:15.598: %STACKMGR-4-SWITCH_ADDED: Switch 1 has been ADDED to the stack
*Jan 2 00:01:17.779: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
*Jan 2 00:01:17.779: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Jan 2 00:01:19.767: %SMI-5-CLIENT: Smart Install Client feature is enabled. It is recommended to disable the Smart Install feature when it is not actively used. To disable feature execute 'no vstack' in configuration mode
*Jan 2 00:01:24.850: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan
*Jan 2 00:01:32.551: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 1 inserted
*Jan 2 00:01:32.551: %PLATFORM_ENV-6-FRU_PS_OIR: FRU Power Supply 2 inserted
*Jan 2 00:01:35.462: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan5, changed state to down
*Jan 2 00:01:35.462: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan25, changed state to down
*Jan 2 00:01:35.521: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan26, changed state to down
*Jan 2 00:01:35.521: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan27, changed state to down
*Jan 2 00:01:35.529: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan28, changed state to down
*Jan 2 00:01:35.529: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan101, changed state to down
*Jan 2 00:01:35.638: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 2 00:01:35.848: %STACKMGR-5-SWITCH_READY: Switch 1 is READY
*Jan 2 00:01:35.848: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 1 Switch 1 has changed to state DOWN
*Jan 2 00:01:35.848: %STACKMGR-4-STACK_LINK_CHANGE: Stack Port 2 Switch 1 has changed to state DOWN
*Jan 2 00:01:36.385: %STACKMGR-5-MASTER_READY: Master Switch 1 is READY
*Jan 2 00:01:37.358: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 15.2(4)E6, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Thu 05-Apr-18 02:22 by prod_rel_team
*Jan 2 00:01:37.475: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down
*Jan 2 00:01:39.354: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to down
*Jan 2 00:01:40.210: %USB_CONSOLE-6-MEDIA_RJ45: Console media-type is RJ45.
*Jan 2 00:01:40.361: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down

Could you try a different IOS? Try the latest 15.0(2)SE train.
You'll need to force the switch to boot into ROMmon and force the switch to boot the IOS using USB.

I have already upgraded it to latest ios: Version 15.2(4)E6, RELEASE SOFTWARE (fc4)

Try a different version. The latest 15.0(2)SE is a good one to use.

Hi Leo

 

Your solution worked. But I dont want it to happen each time the switch reboots. Again after installing the modules the same issue persists. Please suggest a permanent solution to this problem.

Review Cisco Networking for a $25 gift card