12-02-2016 12:10 AM - edited 03-08-2019 08:24 AM
dear support .
i have cisco router
Cisco C867VAE-W-A-K9 i wasn't able to find any documentation for wifi enable on forums .
hope to help me how to enable basic wifi , just wifi with psk and bridged to my lan .
here is my router info below :
==============
Branch1#sh inventory
NAME: "C867VAE-W-A-K9", DESCR: "C867VAE-W-A-K9 chassis, Hw Serial#: GMK200900AV, Hw Revision: 1.0"
PID: C867VAE-W-A-K9 , VID: V01 , SN: GMK200900AV
Branch1#
#########################
Branch1#sh version
Cisco IOS Software, C860 Software (C860VAEW-ADVSECURITYK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 04-Aug-15 06:02 by prod_rel_team
ROM: System Bootstrap, Version 15.3(3r)M1, RELEASE SOFTWARE (fc1)
Branch1 uptime is 4 weeks, 21 hours, 15 minutes
System returned to ROM by reload at 10:48:51 UTC Thu Nov 3 2016
System image file is "flash:c860vaew-advsecurityk9-mz.SPA.153-3.M6.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco C867VAE-W-A-K9 (revision 1.0) with 385024K/32768K bytes of memory.
Processor board ID GMK200900AV
1 DSL controller
1 Ethernet interface
3 FastEthernet interfaces
4 Gigabit Ethernet interfaces
1 ATM interface
1 terminal line
1 Virtual Private Network (VPN) Module
255K bytes of non-volatile configuration memory.
131072K bytes system flash allocated
Configuration register is 0x2102
############################################
kind regards
12-02-2016 12:38 AM
Have you seen this doc it goes through setting up wireless on a 800 series router
http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/configuration/guide/SCG800Guide/SCG800_Guide_BookMap_chapter_01001.html#con_1091378
and this one
http://www.cisco.com/en/US/docs/routers/access/800/880/software/configuration/guide/880_basic_device_wireless_config.html
12-02-2016 12:45 AM
i already tried all other options
none is working
Branch1(config)#service ?
alignment Control alignment correction and logging
call-home Enable call-home service
compress-config Compress the nvram configuration file
config TFTP load config files
counters Control aging of interface counters
dhcp Enable DHCP server and relay agent
disable-ip-fast-frag Disable IP particle-based fast fragmentation
exec-callback Enable exec callback
exec-wait Delay EXEC startup on noisy lines
finger Allow responses to finger requests
hide-telnet-addresses Hide destination addresses in telnet command
linenumber enable line number banner for each exec
nagle Enable Nagle's congestion control algorithm
old-slip-prompts Allow old scripts to operate with slip/ppp
pad Enable PAD commands
password-encryption Encrypt system passwords
prompt Enable mode specific prompt
pt-vty-logging Log significant VTY-Async events
sequence-numbers Stamp logger messages with a sequence number
slave-log Enable log capability of slave IPs
tcp-keepalives-in Generate keepalives on idle incoming network connections
tcp-keepalives-out Generate keepalives on idle outgoing network connections
tcp-small-servers Enable small TCP servers (e.g., ECHO)
telnet-zeroidle Set TCP window 0 when connection is idle
timestamps Timestamp debug/log messages
udp-small-servers Enable small UDP servers (e.g., ECHO)
Branch1(config)#service mo
Branch1(config)#service mo
Branch1(config)#service mo
Branch1(config)#service-module wlan-ap 0 session
^
% Invalid input detected at '^' marker.
Branch1(config)#interface Dot11Radio 0
^
% Invalid input detected at '^' marker.
Branch1(config)#
Branch1(config)#do sh ip int b
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM administratively down down
Dialer0 unassigned YES unset up up
Dialer1 xxxxx YES IPCP up up
Ethernet0 unassigned YES NVRAM up up
FastEthernet0 unassigned YES unset down down
FastEthernet1 unassigned YES unset up up
FastEthernet2 unassigned YES unset down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES NVRAM administratively down down
NVI0 unassigned YES unset administratively down down
Virtual-Access1 unassigned YES unset up up
Vlan1 10.35.90.254 YES NVRAM up up
Wlan-GigabitEthernet0 unassigned YES unset up up
Branch1(config)#
can you give me direct config to my router ??
12-02-2016 12:50 AM
I see you have a wlan interface , see section Starting a Wireless Configuration Session
http://www.cisco.com/en/US/docs/routers/access/800/880/software/configuration/guide/880_basic_device_wireless_config.html
Note Before you configure the wireless settings in the router's setup, you must follow these steps to open a session between the router and the access point.
Enter the following commands in global configuration mode on the router's Cisco IOS CLI.
SUMMARY STEPS
1. interface wlan-ap0
2. ip address subnet mask
3. no shutdown
4. interface vlan1
5. ip address subnet mask
6. exit
7. exit
8. service-module wlan-ap 0 session
DETAILED STEPS
12-02-2016 12:52 AM
Branch1(config)#int Wlan-GigabitEthernet0
Branch1(config-if)#ip ad
Branch1(config-if)#ip add
Branch1(config-if)#ip address 10.35.90.253 255.255.255.0
% IP addresses may not be configured on L2 links.
Branch1(config-if)#
12-02-2016 01:03 AM
Ok this looks a bit closer its needs to be a trunk for that specific interface as below
do a ctrl f on the page and search for ....Configure the wlan-GigabitEthernet0 interface as a trunk
http://www.cisco.com/c/en/us/solutions/collateral/enterprise-networks/virtual-office/white_paper_c11-492842.html
Two additional interfaces exist that are used to communicate with the access-point module: wlan-ap0 and wlan-GigabitEthernet0. You must configure the wlan-ap0 interface with an IP address (any private IP address works; check RFC 1918 for available private subnets) in order to allow reverse Telnet from the router to the access-point module:
Autonomous Mode
12-02-2016 02:27 AM
i still don't see that interface (((wlan-ap0)))
i already configured the interface ((wlan-GigabitEthernet0)) as trunk .
im not sure what to do next !!!
here is config that i have :
Branch1#sh ip int b
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM administratively down down
Dialer0 unassigned YES unset up up
Dialer1 115.70.45.124 YES IPCP up up
Ethernet0 unassigned YES NVRAM up up
FastEthernet0 unassigned YES unset down down
FastEthernet1 unassigned YES unset up up
FastEthernet2 unassigned YES unset down down
GigabitEthernet0 unassigned YES unset down down
GigabitEthernet1 unassigned YES unset down down
GigabitEthernet2 unassigned YES NVRAM administratively down down
NVI0 unassigned YES unset administratively down down
Virtual-Access1 unassigned YES unset up up
Vlan1 10.35.90.254 YES NVRAM up up
Wlan-GigabitEthernet0 unassigned YES unset up up
Branch1#sh run int Wlan-GigabitEthernet0
Building configuration...
Current configuration : 179 bytes
!
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport trunk native vlan 10
switchport mode trunk
no ip address
end
Branch1#
thank you for great response
12-02-2016 03:07 AM
This is a step by step guide using the wlan-G0 you could try that
http://www.firewall.cx/cisco-technical-knowledgebase/cisco-routers/825-cisco880w-multiple-ssid.html
12-02-2016 03:21 AM
i appreciate your kind help .
but again
service-module cmd is not allowed on my router !
Branch1(config)#service-module
^
% Invalid input detected at '^' marker.
Branch1(config)#
also i don't see the interface Dot11Radio0 when i do ,
#sh ip int b
!!!
???
12-02-2016 11:40 PM
what do you think for this issue ??
12-05-2016 03:16 AM
can you help ?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide