02-17-2014 05:10 AM - edited 03-07-2019 06:15 PM
Hi All,
I have a cisco router c2600 version 12.4T. I'm trying to configure the E1 on that router and connectto an eFax server. but it seems that there is some thing wrong in the configuration. Are there anything wrong in the config ??
Current configuration : 2759 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname MAA-FAX
!
boot-start-marker
boot system flash
boot system flash c2600-ipvoice-mz.124-15.T14.bin
boot-end-marker
!
card type e1 1 1
enable secret 5 $1$Eu5N$LNIs2iojGJB.VUSeYS45T1
!
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
!
!
!
!
ip domain name main.knpcdom.net
multilink bundle-name authenticated
isdn switch-type primary-net5
voice-card 1
!
!
!
!
voice service voip
allow-connections h323 to h323
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
h323
!
!
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729br8
!
!
!
!
!
!
!
!
!
!
!
!
!
!
archive
log config
hidekeys
!
!
controller E1 1/0
pri-group timeslots 1-31
!
controller E1 1/1
pri-group timeslots 1-31
!
!
!
!
!
interface FastEthernet0/0
ip address x.x.x.x(voice GW ip) 255.255.255.0
duplex auto
speed auto
h323-gateway voip interface
!
interface Serial1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
interface Serial1/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 x.x.x.x(Voice GW ip -last digit is 1)
!
no ip http server
!
no logging trap
!
!
control-plane
!
!
!
voice-port 1/0:15
!
voice-port 1/1:15
!
!
!
!
!
dial-peer voice 100 voip
preference 2
destination-pattern [1234567890]...
voice-class codec 1
session target ipv4:x.x.x.x (the eFax server ip)
dtmf-relay h245-alphanumeric
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
no vad
!
dial-peer voice 200 pots
destination-pattern 2.......
port 1/0:15
!
dial-peer voice 101 voip
preference 1
destination-pattern [1234567890]...
voice-class codec 1
session target ipv4:x.x.x.x (the eFax backup server ip)
dtmf-relay h245-alphanumeric
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback none
no vad
!
dial-peer voice 10 voip
translation-profile incoming rightfax
voice-class codec 1
incoming called-number 2.......
dtmf-relay h245-alphanumeric
no vad
!
dial-peer voice 2 pots
incoming called-number .
direct-inward-dial
!
dial-peer voice 102 voip
destination-pattern 8...
session target ipv4:x.x.x.x (CUCM ip)
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 103 voip
preference 1
destination-pattern 8...
session target ipv4:x.x.x.x (CUCM backup ip)
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
!
dial-peer voice 1 voip
voice-class codec 1
incoming called-number .
dtmf-relay h245-alphanumeric
no vad
!
!
!
line con 0
password ******
login
line aux 0
line vty 0 4
password ******
login
transport input all
!
!
end
Thank alot
02-20-2014 07:13 AM
I am surprised to see encapsulation hdlc on the serial interfaces. Are you sure that the server is processing hdlc?
HTH
Rick
02-21-2014 01:21 AM
Can you post output of "debug isdn q921" and "debug isdn q931" during attempt to make a call?
HTH,
Dragan
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide