ERROR FW[MOD 05]: LOG - WSC6509-E

[Jaderson Pessoa]

Hello Guys,

Someone know what bout this issue is?

16:13:35.829 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:37.589 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:39.173 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:40.737 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:42.301 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:44.061 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800
16:13:45.661 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF800

Version of the core

Cisco WS-C6509-E ( Intel(R) Core(TM) i3-3227U CPU @ 2.50GHz ) processor (revision )

Cisco IOS Software, s6t64 Software (s6t64-IPSERVICESK9-M), Version 15.5(1)SY1, RELEASE SOFTWARE (fc6)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Sun 04-Mar-18 07:00 by prod_rel_team

ROM: System Bootstrap, Version 15.3(04r)SYS, RELEASE SOFTWARE

[Reza Sharifi]

Hi,

Seems to be an internal bug and there isn't much info publicly available. This post is from 2018.  Cisco TAC may have more info almost 2 years later.

https://community.cisco.com/t5/switching/fw-mod-33-radian-monitor-pll-port-num-12-unit-3-bcmport-5-pll/td-p/3339296

HTH

[Jaderson Pessoa]

Yes, i had checked this and i cant found more information about.

[Reza Sharifi]

Yes, it maybe best to open a ticket with TAC. Hopefully a software upgrade can remedy the issue, if not it may require an RMA.

[Leo Laohoo]

15.5(1)SY1 is pretty old. I'd upgrade the firmware.

[SupportAC]

Hello Jaderson

I know that it was a long time ago, however, could you solved this problem?,

Kind Regards

[Jaderson Pessoa · Accepted solution]

Hello Mr..

After upgrade and reboot the warning were disapear.

Thank you.