06-12-2012 02:16 AM - edited 03-07-2019 07:12 AM
Hello to everyone,
I have a problem with an etherchannel between a cisco 2950 and a couple of catalyst 4506.
The cisco 2950 is connect via an etherchannel to the catalyst 4506A. The channel consist of two port on both side and is in trunk mode, encapsulation dot1q.
Now i have the necessity to connect the 2950 to the other catalyst, 4506B.
So, i copy the same configuration on the 4506B, but when I unplug the two rj45 cables from the catalyst 4506A to plug them in the 4506B the etherchannel doesn't go up in any way.
Sorry i'm becoming crazy.
Have you some idea?
Thank's.
Solved! Go to Solution.
06-12-2012 04:43 AM
I'll throw the obvious out there , are you using crossover cables ? Or did the 4506A have a module that supported mdix while the new does does not ?
06-12-2012 02:36 AM
Hello,
Can you please post the configuration of the EtherChannel both from your 2950 and 4506A and 4506B? Are you trying to have two EtherChannels on 2950 at the same time, one going to 4506A and the second to 4506B?
Best regards,
Peter
06-12-2012 02:51 AM
Yes.
Here you are the configuration of the functioning ethrchannel:
4506A
interface Port-channel5
description *** FEC --> SW2950 ***
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet6/1
description *** FEC --> SW2950 ***
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode on
!
interface GigabitEthernet6/2
description *** FEC --> SW2950 ***
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 5 mode on
2950
interface Port-channel1
description FEC --> SW4506
switchport mode trunk
interface FastEthernet0/23
switchport mode trunk
channel-group 1 mode on
!
interface FastEthernet0/24
switchport mode trunk
channel-group 1 mode on
4506B
interface Port-channel4
description *** FEC --> SW2950 ***
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet5/5
description *** FEC --> SW2950 ***
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode on
!
interface FastEthernet5/6
description *** FEC --> SW2950 ***
switchport trunk encapsulation dot1q
switchport mode trunk
channel-group 4 mode on
The configuration of the 2950 is the same.
Thanks.
06-12-2012 03:06 AM
Hii,
When you copy a running config no shut command is not shown in the running config. so when you copy it no shut command is not present.
So give a no shut command on 4506B catalyst ports and i guess it should work.
HTH,
Sukanya
PS: Please rate helpfull post...
06-12-2012 03:06 AM
Hello,
The configuration seems to be okay so far. How exactly do you know that the EtherChannel does not come up? Are there any logging messages displayed on the console? Any other symptoms, no matter how insignificant they may seem?
Do I understand you correctly that what you do currently is taking the cables from 4506A and plugging them into 4506B, so that on 2950, there is only a single EtherChannel active at any time?
Best regards,
Peter
06-12-2012 04:43 AM
I'll throw the obvious out there , are you using crossover cables ? Or did the 4506A have a module that supported mdix while the new does does not ?
06-12-2012 07:13 AM
I solved,
glen.grant was right it was the most stupid thing. The module WS-X4232-GB-RJ needs the cross cable!!!
Thank to everyone for the support.
06-12-2012 09:04 AM
can try once with the below command with the straight cable if you get chance.
instead of channel group
06-12-2012 12:19 PM
Glen,
+5 points! You're a genius here. I would never think of this although I am aware that 2950 do not have the auto-MDIX functionality. Well done, and thanks for reminding us about these tiny wonderful quirks!
Best regards,
Peter
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide