02-28-2018 07:22 AM - edited 03-08-2019 02:04 PM
In this pkt file I attempt to make
1. IPv6 CONFIG
2. RIPNG
3. EIGRPv6
4. OSPFv3
5. ROUTE REDISTRIBUTION IPv6
6. WAN PPP
I enable ripng NXT-R6 same with NXT-R1, NXT-R2, NXT-R3, NXT-R4, NXT-R5 with this
The running config is in spoiler below
ipv6 rip NIXTRAIN enable to some connected port and ipv6 router rip NIXTRAIN
NXT-R1#sh running-config Building configuration... Current configuration : 799 bytes version 15.1 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption hostname NXT-R1 ip cef ipv6 unicast-routing no ipv6 cef license udi pid CISCO1941/K9 sn FTX15247S2V spanning-tree mode pvst interface Loopback1 no ip address ipv6 address 1:1:1:1::1/128 ipv6 rip NIXTRAIN enable interface GigabitEthernet0/0 no ip address duplex auto speed auto ipv6 address 12:12:12:12::1/64 ipv6 rip NIXTRAIN enable interface GigabitEthernet0/1 no ip address duplex auto speed auto shutdown interface Vlan1 no ip address shutdown ipv6 router rip NIXTRAIN ip classless ip flow-export version 9 line con 0 line aux 0 line vty 0 4 login end
NXT-R6#sh running-config Building configuration... Current configuration : 922 bytes version 15.1 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption hostname NXT-R6 no ip cef ipv6 unicast-routing no ipv6 cef license udi pid CISCO1941/K9 sn FTX1524X132 spanning-tree mode pvst interface GigabitEthernet0/0 no ip address duplex auto speed auto ipv6 address 56:56:56:56::6/24 interface GigabitEthernet0/1 no ip address duplex auto speed auto ipv6 address 67:67:67:67::7/24 ipv6 rip NIXTRAIN enable interface Serial0/0/0 no ip address ipv6 address 610:610:610:610::6/64 ipv6 rip NIXTRAIN enable clock rate 2000000 interface Serial0/0/1 no ip address clock rate 2000000 shutdown interface Vlan1 no ip address shutdown ipv6 router rip NIXTRAIN ip classless ip flow-export version 9 line con 0 line aux 0 line vty 0 4 login end
NXT-R10#sh running-config Building configuration... Current configuration : 1033 bytes version 15.1 no service timestamps log datetime msec no service timestamps debug datetime msec no service password-encryption hostname NXT-R10 no ip cef ipv6 unicast-routing no ipv6 cef license udi pid CISCO1941/K9 sn FTX1524CP42 spanning-tree mode pvst interface GigabitEthernet0/0 no ip address duplex auto speed auto ipv6 address 1011:1011:1011:1011::10/64 ipv6 eigrp 1 interface GigabitEthernet0/1 no ip address duplex auto speed auto shutdown interface Serial0/0/0 no ip address ipv6 address 610:610:610:610::10/64 ipv6 rip NIXTRAIN enable interface Serial0/0/1 no ip address clock rate 2000000 shutdown interface Vlan1 no ip address shutdown ipv6 router eigrp 1 eigrp router-id 10.10.10.10 no shutdown redistribute rip NIXTRAIN metric 1544 20000 255 1 1500 ipv6 router rip NIXTRAIN redistribute eigrp 1 metric 2 ip classless ip flow-export version 9 line con 0 line aux 0 line vty 0 4 login end
but NXT-R6 cant access other router with more than 1 hop & cant access NXT-R10 too.
And how command redistribute from ripng to eigrp v6? with my case
Is there need route distribution from NXT-R6 to NXT-R10? because in NXT-R10 I use route redistribtion.
from NXT-R10 I Can ping until NXT-R25.
Any configuration I missed?
pkt file : https://drive.google.com/open?id=1fMx3bTG6H2Vv66bujFA-ZZbN4d4cIppm
Thanks in advance
03-01-2018 12:46 AM
Up
03-02-2018 07:15 AM
Up
03-05-2018 03:09 PM
up
03-07-2018 12:31 AM
03-09-2018 06:09 PM
up
03-10-2018 10:22 AM
Hi
Your configuration looks fine, try adding the following word:
ipv6 router eigrp 1 eigrp router-id 10.10.10.10 no shutdown redistribute rip NIXTRAIN metric 1544 20000 255 1 1500 include-connected ipv6 router rip NIXTRAIN redistribute eigrp 1 metric 2 include-connnected
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide