11-25-2011 05:47 AM - edited 03-07-2019 03:36 AM
Hi..
on IOS versions higher than 12.2(50) on Cisco 3560G-48TS I get this error/traceback, when I reach a certain number of Access-lists group'ed to "interface vlan", and the ACL inserted in the TCAM reaches acl label #128 (can be seen with : Show platform acl label 128)
I can see errors in the TCAM if I issue the command:
udj#sh platform tcam errors
TCAM Memory Consistency Checker Errors
--------------------------------------
TCAM Space Values Masks Fixups Retries Failures
Unassigned 0 0 0 0 0
HFTM 0 0 0 0 0
HQATM 26 0 26 0 0
I have upgraded from 12.2(35), bacause this version dropped all traffic when I reached an ACL that was inserted in the TCAM as ACL label 128, and actually this is not the problem with later versions, but now they spit out these syslog messages very frequently and I am reluctant to put this into production
Anyone have any thoughts on what is going on and how I can circumvent this problem and have ALL my ACL's be functioning at the same time (hardware or software). This should not be a hard limit reached in the TCAM, so I am guessing it might be a (another) bug?
Thanks..
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz2
000160: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000161: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000162: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000163: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000164: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000165: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000166: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000167: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000168: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000169: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000170: 00:05:23: platform assert failure: 0: ..ulc_tcam.c: 1216: htd_cam_value_read32
000171: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000172: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000173: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000174: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000175: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000176: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000177: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Space and not able to recover the error
-Traceback= 2320548z 1AD572Cz 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz2
000160: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000161: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000162: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000163: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000164: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000165: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000166: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000167: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000168: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000169: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000170: 00:05:23: platform assert failure: 0: ..ulc_tcam.c: 1216: htd_cam_value_read32
000171: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000172: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000173: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000174: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1216: htd_cam_value_read32
000175: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F7274z 1AD56A0z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
000176: 00:05:23: platform assert failure: 0: ../src-hulc/src-sasq/hulc_tcam.c: 1109: htd_cam_value_write32
000177: 00:05:23: -Traceback= 2321FA0z 16E6D08z 18F6F30z 1AD5688z 1AD8B5Cz 1AD8E30z 18FB74Cz 1CC43E8z 1CBE25Cz
Kind regards,
Ulrik
12-03-2011 03:12 PM
Hello Ulrik,
The Error message indicates the following, the switch cannot fix a ternary content addressable memory (TCAM) integrity error. [chars] is memory location with the error: Unassigned TCAM Space, HFTM TCAM Space (the ASIC forwarding TCAM manager space), or HQATM TCAM Space (the TCAM ASIC quality of service [QoS] and access control list [ACL] TCAM manager space)
The solution is to hard reboot the switch once and see if this error message is going away.
If error message appears after hard reboot please post the below ouput,
1) show platform tcam utilization
2) show platform tcam usage
3) show platform tcam log-results
Thanks,
Ricky Micky
*Rate Useful Posts
12-05-2011 04:16 AM
The errors are persistent, so I get the same errors efter "power off -> power on"..
The TCAM usage is:
L3AccessSW10audj#sh platform tcam errors
TCAM Memory Consistency Checker Errors
--------------------------------------
TCAM Space Values Masks Fixups Retries Failures
Unassigned 0 0 0 0 0
HFTM 0 0 0 0 0
HQATM 51 0 27 120 24
L3AccessSW10audj#sh platform tcam utilization
CAM Utilization for ASIC# 0 Max Used
Masks/Values Masks/values
Unicast mac addresses: 528/4224 31/162
IPv4 IGMP groups + multicast routes: 152/1216 6/26
IPv4 unicast directly-connected routes: 528/4224 31/162
IPv4 unicast indirectly-connected routes: 280/2240 12/54
IPv4 policy based routing aces: 512/512 2/2
IPv4 qos aces: 768/768 324/324
IPv4 security aces: 1024/2048 306/1314
Note: Allocation of TCAM entries per feature uses
a complex algorithm. The above information is meant
to provide an abstract view of the current TCAM utilization
L3AccessSW10audj#sh platform tcam usage
=============================================================================
TCAM Table
TCAM / SSRAM Table TCAM SSRAM
Start Size X Start Size Y
=============================================================================
Local Forwarding Table: 0 1540 1 0 1540 4
Local Learning Table: 0 1540 1 5500 1540 2
Secondary Forwarding Table: 1080 1D80 1 7F80 1D80 8
QoS Table: 2E00 1800 1 1F780 1800 4
ACL Table: 4600 2000 1 25780 2000 4
IPV6 Secondary Forwarding Tabl 7D80 180 2 1F180 C0 8
IPV6 Classification Table: 7F00 80 2 2D780 40 4
IPV6 ACL Table: 7F80 70 2 2D880 38 4
Station Table: 0 0 0 2D980 1540 4
MAC Address Table: 0 0 0 32E80 1000 8
Multicast Expansion Table: 0 0 0 3AE80 422 8
VLAN List Table: 0 0 0 3E000 400 10
Equal Cost Route Table: 0 0 0 3D000 80 20
X - Number of 144-bit TCAM entries per descriptor
Y - Number of bytes per descriptor
=============================================================================
SDM template realignment scheme-1 in effect
L3AccessSW10audj#sh platform tcam log-results
================================================================
CAM Log Results
----------------------------------------------------------------
Total Number of PortASICs: 13
ASIC 0
Lookup "Invalid", value 0
TCAM Index 94207, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFF-EFF7FFFF
key-1: FF-FFFFFFFF-EFF7FFFF
key-2: CF-FFFFFFFF-FDFFFFF7
key-3: FF-BFFFFFF5-FFFFFFFF
ASIC 1
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: 09-10030020-30402CC1
key-1: 09-10030020-30402CC1
key-2: 40-00000404-91812040
key-3: 47-15BCEF08-82E80940
ASIC 2
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00400000-00000000
key-1: 00-00000010-00000000
key-2: 00-00000000-00000800
key-3: 04-00000000-00000000
ASIC 3
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000200-00000000
key-1: 00-00000200-00000000
key-2: 00-00000000-00000000
key-3: 00-00000000-00000000
ASIC 4
Lookup "Invalid", value 0
TCAM Index 100560, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000000-00000000
key-1: 00-22000100-00200000
key-2: 00-00000000-00080000
key-3: 00-00000000-00000000
ASIC 5
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 80-0C000000-20000000
key-1: 00-0A000000-10004000
key-2: 0C-00200000-00000000
key-3: 00-00000000-00000000
ASIC 6
Lookup "Invalid", value 0
TCAM Index 4096, TCAM Table Index -1
Cam Log Keys
key-0: 00-870C0004-00200020
key-1: 08-00000000-01200000
key-2: 00-00000010-50000040
key-3: 00-00000000-00400000
ASIC 7
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000400-00000000
key-1: 00-04010000-00000000
key-2: 00-00000000-00000000
key-3: 00-00000000-00002000
ASIC 8
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000000-00000000
key-1: 00-00000000-00000000
key-2: 00-00000000-00000000
key-3: 00-00000000-40000000
ASIC 9
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000000-00000000
key-1: 00-00000000-00000000
key-2: 00-00000000-00000000
key-3: 50-00000000-00000000
ASIC 10
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000000-00000000
key-1: 00-00000000-00000000
key-2: 00-00000000-00000000
key-3: 00-00000000-00000000
ASIC 11
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00200000-40040000
key-1: 00-00000000-00040000
key-2: 00-00000000-00000000
key-3: 00-00000000-00000000
ASIC 12
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: 00-00000000-00010000
key-1: 00-28000000-00280000
key-2: 00-00000000-000040C4
key-3: 00-0000040C-00040004
Notes:
a) key-0 is most recent cam key
b) key-0 contains lsb's and key-3 contains msb's
c) watch for Lookup field in cam key for validating results
d) TCAM Table Index -1 indicates invalid results
================================================================
L3AccessSW10audj#
12-05-2011 04:20 AM
The switch is running the following verison at the moment (have testet various IOS versions)
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 52 WS-C3560G-48TS 15.0(1)SE C3560-IPSERVICESK9-M
12-05-2011 06:05 PM
Hello,
As i said earlier, this error message is thrown when there is a TCAM corruption and the TCAM consistency check routines on the switch haven't been able to correct the corruption that has happened. Hence the syslog is thrown.
70% of the time rebooting the switch corrects this function incase if this doesn't gets corrected you would need a hardware replacement.
Thanks,
Richard
*Rate useful posts
12-06-2011 05:01 AM
The thing is, that these errors only show, when ACL label 128 is in use .. everything is quiet untill I access-group the final Access-list, and then the above bitching and TCAM errors begin
It does seem like a firmware (or hardware) bug, it is probably not a coincidense that 0-127 works fine and the problem begins at 128.
Do I understand you correctly, when I hear you saying the Hardware is faulty, and should be replaced (with another C3560G)?
(I have only testet on a spare part we had in stock .. I'll see if I can find another C3560G to test.)
Thanks..
08-04-2014 03:06 PM
Hello,
I have this problem too, but keep going after the reboot.
error:
%HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888484 888E9C 88B418 88C0B8 6F1380 1515690 150C100
2090102: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888740 888F4C 88B418 88C0B8 6F1380 1515690 150C100
2090103: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888484 8893A8 88BAE0 88C0B8 6F1380 1515690 150C100
2090104: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888740 88991C 88BAF0 88C0B8 6F1380 1515690 150C100
2090105: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888484 889C50 88BB00 88C0B8 6F1380 1515690 150C100
2090106: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888484 889FB8 88BB10 88C0B8 6F1380 1515690 150C100
2090107: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888740 88A08C 88BB10 88C0B8 6F1380 1515690 150C100
2090108: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
-Traceback= 888740 88A08C 88BB10 88C0B8 6F1380 1515690 150C100
2090109: Aug 4 17:00:41: %HARDWARE-1-TCAM_ERROR: Found error in HQATM TCAM Spac
e and not able to recover the error
Here it's th output for the show command you required.
1) show platform tcam utilization
CAM Utilization for ASIC# 0 Max Used
Masks/Values Masks/values
Unicast mac addresses: 1040/8320 103/742
IPv4 IGMP groups + multicast routes: 56/448 6/26
IPv4 unicast routes: 0/0 0/0
IPv4 policy based routing aces: 0/0 0/0
IPv4 qos aces: 384/384 260/260
IPv4 security aces: 384/384 39/39
Note: Allocation of TCAM entries per feature uses
a complex algorithm. The above information is meant
to provide an abstract view of the current TCAM utilization
2)
show platform tcam usage
=============================================================================
TCAM Table
TCAM / SSRAM Table TCAM SSRAM
Start Size X Start Size Y
=============================================================================
Local Forwarding Table: 0 2240 1 0 2240 4
Local Learning Table: 0 2240 1 8900 2240 2
Secondary Forwarding Table: 2080 240 1 CD80 240 8
QoS Table: 22C0 C00 1 FC80 C00 4
ACL Table: 2EC0 C00 1 12C80 C00 4
IPV6 Secondary Forwarding Tabl 3E40 C0 2 DF80 60 8
IPV6 Classification Table: 3F00 80 2 15C80 40 4
IPV6 ACL Table: 3F80 70 2 15D80 38 4
Station Table: 0 0 0 15E80 2240 4
MAC Address Table: 0 0 0 1E780 2 8
Multicast Expansion Table: 0 0 0 1E800 122 8
VLAN List Table: 0 0 0 1F180 40 10
Equal Cost Route Table: 0 0 0 1F180 0 20
X - Number of 144-bit TCAM entries per descriptor
Y - Number of bytes per descriptor
=============================================================================
SDM template realignment scheme-2 in effect
Dummy SFD start: 0xEA80, entries 0x240, size 8
3)
show platform tcam log-results
================================================================
CAM Log Results
----------------------------------------------------------------
Total Number of PortASICs: 12
ASIC 0
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFF9F9C3-FEE17FBF
key-1: FF-FFF9F9C3-FEE17FBF
key-2: FF-FFFFFFFF-FFFFBFFF
key-3: FF-FFFFFFFF-AFFFDFFF
ASIC 1
Lookup "Invalid", value 0
TCAM Index 32768, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFF-FFFFFFFF
key-1: FF-FFFFFFFF-FFFFFFFF
key-2: FF-FFFFFFFF-FFFFFFFF
key-3: 00-00000000-00000090
ASIC 2
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-7FFFFF5F-FFFFFFFE
key-1: FF-7FFFFF5F-FFFFFFFE
key-2: FF-7FFFFF5F-FFFFFFFE
key-3: FF-FFFF7FFF-FFFFFF7F
ASIC 3
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FBFF7FFF-FFBFFFFF
key-1: FF-FBFF7FFF-FFBFFFFF
key-2: D7-FFFFF47D-BDEFFFFF
key-3: DB-BFFFF95F-9CEFFFE0
ASIC 4
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFEF-FEFFDFE5
key-1: FF-FFFFFFEF-FEFFDFE5
key-2: D7-FFFFEF9D-F3FF7FFF
key-3: DF-9F5FFBFF-EDFBEE7F
ASIC 5
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFF-FFFFFFFF
key-1: FF-FFFFFFFF-FFFFFFFF
key-2: FF-FFFFFFFF-FFFFFFFF
key-3: FF-FFFFFEE8-37F3FFFF
ASIC 6
Lookup "Invalid", value 0
TCAM Index 116735, TCAM Table Index -1
Cam Log Keys
key-0: F7-FFFFFFFF-B7FF7FEF
key-1: 78-302A1023-8F69760C
key-2: ED-FFF7EFFF-FFFD6DFF
key-3: E8-FFD7FFFF-DFDFAFFF
ASIC 7
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFBFFFFF-FFFFFFFE
key-1: FF-FFBFFFFF-FFFFFFFE
key-2: FF-FFBFFFFF-FFFFFFFE
key-3: FF-7DFDF85F-F2E9FFF7
ASIC 8
Lookup "Invalid", value 0
TCAM Index 131071, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFF-FFFFFFFF
key-1: FF-FFFFFFFF-FFFFFFFF
key-2: 2F-FFFEFFFF-FFFFFFDF
key-3: FF-B9FEFFDF-DEFEBBFF
ASIC 9
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFE-FFFFFFFF
key-1: FF-FFFFFFFE-FFFFFFFF
key-2: FF-FFFFFFFE-FFFFFFFF
key-3: FF-FBDFFE71-CFFFFFFF
ASIC 10
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FFFFFFFF-F7FFFFFF
key-1: FF-FFFFFFFF-F7FFFFFF
key-2: FF-7FFDFFFF-7FA6F7FD
key-3: 9C-7FDFFFF6-7DF3FE75
ASIC 11
Lookup "Invalid", value 0
TCAM Index 0, TCAM Table Index -1
Cam Log Keys
key-0: FF-FBFFFF7F-EFFFFFFF
key-1: FF-FBFFFF7F-EFFFFFFF
key-2: EF-FFFFFFFF-FFFFFFFB
key-3: E3-EFFFFFF6-B7FFFFFF
Notes:
a) key-0 is most recent cam key
b) key-0 contains lsb's and key-3 contains msb's
c) watch for Lookup field in cam key for validating results
d) TCAM Table Index -1 indicates invalid results
================================================================
Hope you can help us, I look forward yor answer.
Best regards,
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide