Hey guys. I'm still in the early stages of this stuff. I have a Cisco 1841 router double NATing from my ISP router. My 1841 router is then connected to switch 1 via Fa0/1. Switch 1 is connected to switch 2 via Fa0/13 on both switches.I trunked it. So if I have some ports set for Vlan 50 on both switches why would they not be able to ping each other? I may have some leftover configurations in these outputs but I tried to clear out everything from the messing around I did previous to this. Please let me know what I am doing wrong.This is driving me crazy. Suggestions for configs for starting anew (that would help me all the same)? All I want to do is set up a VLAN that spans across two switches and allows me to ping between hosts on that same VLAN that are connected to different switches. I am at my wits end. Also, this is not an issue of firewalls blocking the pings. I am sure of that, as I have temporarily turned them off and was able to ping in other scenarios I have set up in the past. Below are configs for Sw1 and 2.
Thank you,
Switch#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/3, Fa0/4, Fa0/6
Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/22, Fa0/23
Fa0/24, Gi0/1, Gi0/2
50 VLAN0050 active Fa0/2, Fa0/5
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
Switch#
Switch#
Switch#show running-config
Building configuration...
Current configuration : 1303 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch
!
!
no aaa new-model
system mtu routing 1500
ip subnet-zero
!
!
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface FastEthernet0/1
!
interface FastEthernet0/2
switchport access vlan 50
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
switchport access vlan 50
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
switchport mode trunk
!
interface FastEthernet0/14
!
interface FastEthernet0/15
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface Vlan1
ip address dhcp
no ip route-cache
!
ip http server
ip http secure-server
!
control-plane
!
!
line con 0
line vty 5 15
!
end
Switch#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/13 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/13 1-4094
Port Vlans allowed and active in management domain
Fa0/13 1,50
Port Vlans in spanning tree forwarding state and not pruned
Fa0/13 1,50
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
And Switch 2:
Switch2#show running-config
Building configuration...
Current configuration : 1495 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Switch2
!
!
no aaa new-model
system mtu routing 1500
ip subnet-zero
!
!
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface Port-channel1
!
interface FastEthernet0/1
switchport access vlan 99
switchport mode access
!
interface FastEthernet0/2
switchport access vlan 50
!
interface FastEthernet0/3
!
interface FastEthernet0/4
!
interface FastEthernet0/5
!
interface FastEthernet0/6
!
interface FastEthernet0/7
!
interface FastEthernet0/8
!
interface FastEthernet0/9
!
interface FastEthernet0/10
!
interface FastEthernet0/11
!
interface FastEthernet0/12
!
interface FastEthernet0/13
!
interface FastEthernet0/14
channel-group 1 mode on
!
interface FastEthernet0/15
channel-group 1 mode on
!
interface FastEthernet0/16
!
interface FastEthernet0/17
!
interface FastEthernet0/18
!
interface FastEthernet0/19
!
interface FastEthernet0/20
!
interface FastEthernet0/21
!
interface FastEthernet0/22
switchport access vlan 99
!
interface FastEthernet0/23
!
interface FastEthernet0/24
!
interface GigabitEthernet0/1
switchport access vlan 99
switchport mode dynamic desirable
!
interface GigabitEthernet0/2
!
interface Vlan1
no ip address
no ip route-cache
!
ip http server
ip http secure-server
!
control-plane
!
!
line con 0
line vty 0 4
login
line vty 5 15
login
!
end
Switch2#show interface trunk
Port Mode Encapsulation Status Native vlan
Fa0/13 auto 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/13 1-4094
Port Vlans allowed and active in management domain
Fa0/13 1,50
Port Vlans in spanning tree forwarding state and not pruned
Fa0/13 1,50
Switch2#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/3, Fa0/4, Fa0/5, Fa0/6
Fa0/7, Fa0/8, Fa0/9, Fa0/10
Fa0/11, Fa0/12, Fa0/14, Fa0/15
Fa0/16, Fa0/17, Fa0/18, Fa0/19
Fa0/20, Fa0/21, Fa0/23, Fa0/24
Gi0/2
50 VLAN0050 active Fa0/2
1002 fddi-default act/unsup
1003 token-ring-default act/unsup
1004 fddinet-default act/unsup
1005 trnet-default act/unsup
