06-22-2021 12:57 AM
Dear community,
I have two 9410Rs (core) and two 9407R(distribution) switches. I have attached the specific details of their components below.
I need to configure high availability at core and distribution level. Which design would be ok to take in this case is it VSS or stacking? If stacking with the components included will I be able to achieve this? any reference on documentation on how to make the physical/logical connections would be welcomed.
Thanks you all!
Regards,
Isaac.
Solved! Go to Solution.
06-22-2021 02:33 AM - edited 06-22-2021 02:34 AM
Hello @isaaco001 ,
from a design point of view I think that you can do the following:
VSS and SVL are limited to only two devices
so you can:
a) create an SVL pair between the core C9410R switches
b) create an SVL pair between the distribution C9407R switches
c) you can configure a L3 multi chassis port channel 4 X 10G so that whatever chassis is alive core01, core02 Dis01 dis02 there is at least one working link between them
core01 --- Dis01
core01 -- Dis02
core02--- Dis01
core02 -- Dis02
On the port-channel you run a routing protocol like OSPF.
Hope to help
Giuseppe
06-22-2021 09:30 AM
06-22-2021 01:13 AM - edited 06-22-2021 01:15 AM
@isaaco001 wrote:
C9400-SSD-240GB
Have you seen this: Free SSD for Cisco ThousandEyes Hosting:
A customer making a new purchase of selected Catalyst 9300 Series and Catalyst 9400 Series Switches with a Cisco DNA Advantage or Premier license will receive a free SSD, either 120GB or 240GB, based on the switch model being purchased.
And what about this: Wired-Plus-Wireless Promotion
Buy one Catalyst 9400 7-slot or 10-slot modular switch with 1 Catalyst 9400 2x multigigabit line card with a Cisco DNA Advantage or Premier license, and get 4 Catalyst 9130 Access Points free.
06-22-2021 02:33 AM - edited 06-22-2021 02:34 AM
Hello @isaaco001 ,
from a design point of view I think that you can do the following:
VSS and SVL are limited to only two devices
so you can:
a) create an SVL pair between the core C9410R switches
b) create an SVL pair between the distribution C9407R switches
c) you can configure a L3 multi chassis port channel 4 X 10G so that whatever chassis is alive core01, core02 Dis01 dis02 there is at least one working link between them
core01 --- Dis01
core01 -- Dis02
core02--- Dis01
core02 -- Dis02
On the port-channel you run a routing protocol like OSPF.
Hope to help
Giuseppe
06-22-2021 11:37 AM
Giuseppe,
Thanks for you prompt and informative response!
I understood steps a and b well.Step c is a good idea but I didn't understand how I can achieve this. c ) you can configure a L3 multi chassis port channel 4 X 10G so that whatever chassis is alive core01,core02 Dis01 dis02 there is at least one working link between them.
Are you saying we have:
P2P port-channel(10G) between Dis01 to core01,P2P port-channel(10G) between Dis01 to core02?
P2P port-channel(10G) between Dis02 to core01,P2P port-channel (10G) between Dis02 to core02?
Then run OSPF between all the P2Ps?
This HA setup(core/distribution) is totally new to me so to also clarify, If let say my core switch is performing roles such as the gateway of all internal networks, running dhcp service,connecting to perimiter firewall etc. what will be the role of the distribution? will it just be providing connectivity and redundancy...essentially "passing along" the connections to the core switch!
If you have any sample configurations or references/links of such setups of the overall connectivity, kindly share!
Regards,
Isaac
06-22-2021 02:14 PM
Hello @isaaco001 ,
I proposed to create an SVL for core switches and an SVL pair for distribution .
When you do this each SVL pait appears aa a single device to the outer world I have proposed to creat a port-channel between the two pairs with a careful choice of member links so that at least one member link is alive in case of a single chassis failiure a both core SVL and distribution SVL pairs.
>> If let say my core switch is performing roles such as the gateway of all internal networks, running dhcp service,connecting to perimiter firewall etc. what will be the role of the distribution? will it just be providing connectivity and redundancy...essentially "passing along" the connections to the core switch!
In this case if all L3 routing functions are done at Core layer you should use a L2 trunk on the port channel but it would be a waste of reosources to use the distribution just to aggregate access layer switches.
I would suggest to consider moving inter VLAN routing to distribution for user facing VLANs
Hope to help
Giuseppe
06-23-2021 02:32 AM
Giuseppe,
Thanks once again for clarification. The logical connectivity now makes perfect sense!
Just one last query,
Physically this would mean I have connections connecting from DSO1<---->CS01,DSO1<--->CS02 and DSO2<---->CS01,DSO2<--->CS02 all members of the same portchannel?
And SVL physical links between CS01<===>CS02 and DS01<===>DSO2?
Regards,
Isaac
06-23-2021 02:43 PM
Hello @isaaco001 ,
>>
Physically this would mean I have connections connecting from DSO1<---->CS01,DSO1<--->CS02 and DSO2<---->CS01,DSO2<--->CS02 all members of the same portchannel?
And SVL physical links between CS01<===>CS02 and DS01<===>DSO2?
Yes your understanding is correct , you need to create SVL pairs first then the port channel multi chassis between the two pairs
Hope to help
Giuseppe
06-22-2021 09:30 AM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide