cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1422
Views
10
Helpful
8
Replies

How to configure wakeonlan from one pc to another on the same vlan

Mike-
Level 1
Level 1

How to configure wakeonlan from one pc to another on the same vlan and same subnet.

I have tried configuring a static entry in the  arp and mac address table without success.

A packet capture from the wol source only shows an arp request being sent.

Is there a way to accomplish this?

1 Accepted Solution

Accepted Solutions

Mike-
Level 1
Level 1

Thanks for all the reply's.

 

On this Intel Gigabit 4 port NIC in this older Dell R620.

I had to Enable PME and disable Energy Efficient Ethernet by going to Device manager -> NIC 1 properties -> Advanced Tab.

Also, under the Power Management Tab in device manager, I checked "Only allow a magic packet to wake the computer".

 

 

View solution in original post

8 Replies 8

balaji.bandi
Hall of Fame
Hall of Fame

what is the device and IOs code running,  How is your config look like, what kind of end device ?

 

Look below document for reference.

https://www.cisco.com/c/en/us/support/docs/switches/catalyst-3750-series-switches/91672-catl3-wol-vlans.html

BB

***** Rate All Helpful Responses *****

How to Ask The Cisco Community for Help

Source is raspberry pi 4 with wakeonlan package installed. (apt install wakeonlan)

Destination is Dell R620 nic1 with wake on lan enabled in bios.

 

Switch Model - C2960L
IOS Version 15.2(5r)E3

 Below is config for both pi and R620 interface

switch.lan# show run int gi0/7
!
interface GigabitEthernet0/7
 description Raspberry pi
 switchport access vlan 20
 no lldp receive

switch.lan#show run int gi0/6
!
interface GigabitEthernet0/6
 description Dell R620 i
 switchport access vlan 20
 no lldp receive
end

 

Hello

First of all have you enabled WOL in the PC's nic cards?


Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul

Source is raspberry pi 4 with wakeonlan package installed. (apt install wakeonlan)

Destination is Dell R620 nic1 with wake on lan enabled in bios.

 

Switch Model - C2960L

IOS Version 15.2(5r)E3

Hello,

 

make sure the power management settings of your NIC are set as in the pictures attached (in addition to the WOL settings).

 

I only know etherwake for the Raspberry, but I assume wakeonlan works the same. I think you have to sudo the command from the server, it should look something like this:

 

sudo etherwake -i eth0 00:c0:ad:cd:ef:ce

Hello,

 

which Wake on Lan tool are you using (e.g. Nirsoft/Depicus) ?

Hello


@Georg Pauwen wrote:

which Wake on Lan tool are you using (e.g. Nirsoft/Depicus) ?


??? what are these for - can you elaborate?


Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.

Kind Regards
Paul

Mike-
Level 1
Level 1

Thanks for all the reply's.

 

On this Intel Gigabit 4 port NIC in this older Dell R620.

I had to Enable PME and disable Energy Efficient Ethernet by going to Device manager -> NIC 1 properties -> Advanced Tab.

Also, under the Power Management Tab in device manager, I checked "Only allow a magic packet to wake the computer".

 

 

Review Cisco Networking for a $25 gift card