10-23-2020 09:35 AM - edited 10-23-2020 09:36 AM
Hi.. I have a few refurbished ws-c3850-24P switches and one of the has ACLs and I do not know how to remove them properly, please help. Thank you! - Bill (see below). I did erase the startup-config and reloaded, but these entries did not go away.
ip access-list extended AutoQos-4.0-wlan-Acl-Bulk-Data
permit tcp any any eq 22
permit tcp any any eq 465
permit tcp any any eq 143
permit tcp any any eq 993
permit tcp any any eq 995
permit tcp any any eq 1914
permit tcp any any eq ftp
permit tcp any any eq ftp-data
permit tcp any any eq smtp
permit tcp any any eq pop3
ip access-list extended AutoQos-4.0-wlan-Acl-MultiEnhanced-Conf
permit udp any any range 16384 32767
permit tcp any any range 50000 59999
ip access-list extended AutoQos-4.0-wlan-Acl-Scavanger
permit tcp any any range 2300 2400
permit udp any any range 2300 2400
permit tcp any any range 6881 6999
permit tcp any any range 28800 29100
permit tcp any any eq 1214
permit udp any any eq 1214
permit tcp any any eq 3689
permit udp any any eq 3689
permit tcp any any eq 11999
ip access-list extended AutoQos-4.0-wlan-Acl-Signaling
permit tcp any any range 2000 2002
permit tcp any any range 5060 5061
permit udp any any range 5060 5061
ip access-list extended AutoQos-4.0-wlan-Acl-Transactional-Data
permit tcp any any eq 443
permit tcp any any eq 1521
permit udp any any eq 1521
permit tcp any any eq 1526
permit udp any any eq 1526
permit tcp any any eq 1575
permit udp any any eq 1575
permit tcp any any eq 1630
permit udp any any eq 1630
permit tcp any any eq 1527
permit tcp any any eq 6200
permit tcp any any eq 3389
permit tcp any any eq 5985
permit tcp any any eq 8080
10-23-2020 09:55 AM
You want to do factory reset :
config t
!
factory-reset config << this will remove all the config.
!
reload and test
10-23-2020 02:39 PM
Couldn't get this to work? - didn't recognize the command. Thanks anyway. - Bill
10-23-2020 10:38 AM
Hi,
In addition to "erase startup-config" use "write erase" and then reboot.
If none of these works, use the mode button:
using an earlier release, you can skip this step.
Press and hold the Mode button. The switch LEDs begin blinking after about 3 seconds.
Continue holding down the Mode button. The LEDs stop blinking after 7 more seconds, and then the switch restarts.
The switch now operates like an unconfigured switch.
Link:
HTH
10-24-2020 04:34 AM - edited 10-24-2020 04:45 AM
Hello
I think you may find these are default to the software of the switch when auto qos is enabled, So disable auto qos, delete and reload or as stated erase startup-config and reload switch.
10-26-2020 10:14 AM
Hi Paul.. thanks for your reply.. I believe you are correct and I have been searching for the way to just "disable" autoquos, but have not found it simple.. is there a command to just Disable it, or is it complicated? Thanks for your help.. I've been setting up Cisco switches for many years, but have not dealt with this. Thanks again. - Bill
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide