02-24-2011 08:23 AM - edited 03-06-2019 03:44 PM
Hello Experts ,
any idea for below drop.
#sh controllers TenGigE0/3/0/0 stats
Ingress:
Input total bytes = 184983908201609
Input good bytes = 184983908193483
Input total packets = 476570253226
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 1051589535
Input pkts 65-127 bytes = 198638861313
Input pkts 128-255 bytes = 113898515084
Input pkts 256-511 bytes = 54986973113
Input pkts 512-1023 bytes = 39923316859
Input pkts 1024-1518 bytes = 41648349441
Input pkts 1519-Max bytes = 26422647884
Input good pkts = 476570253212
Input unicast pkts = 476567711194
Input multicast pkts = 2542016
Input broadcast pkts = 2
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input error giant = 0
Input error runt = 0Input drop other = 3920127
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 12
Input error collisions = 0
Input error symbol = 0
Input error other = 2
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 12
#sh interfaces TenGigE0/3/0/0
60298924302 packets input, 25287858986470 bytes, 70389 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 298092 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
69305800973 packets output, 29793241284072 bytes, 0 total output drops
Output 0 broadcast packets, 309639 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Regards
Mahesh
Solved! Go to Solution.
02-26-2011 07:33 PM
Is this drop rate is a concern?
What is the plim type?
What's going on the other ports on that plim?
Have you tested L1?
Can u get the plim asic stat?
Sent from Cisco Technical Support iPhone App
02-25-2011 10:36 PM
Hello Guys,
Any idea ?
This is happening with almost every gig interface for node migrated to IOS-XR. But yes there is no customer complaint.
Regards
Mahesh
02-26-2011 07:33 PM
Is this drop rate is a concern?
What is the plim type?
What's going on the other ports on that plim?
Have you tested L1?
Can u get the plim asic stat?
Sent from Cisco Technical Support iPhone App
02-27-2011 06:37 AM
Hello Yigal,
Nice to know that you are active on community .
Well answers to your questions.
Is this drop rate is a concern?
> No. And that is the reason I did not log tac case and prefer to get answer from community.
What is the plim type?
> SPA-1X10GE-L-V2
What's going on the other ports on that plim?
> Port is admin down (Teng0/6/1)
Have you tested L1?
> Yes, 24 hour test without any issue found.
Can u get the plim asic stat?
> command (sh controllers plim asic statistics interface <>) is not working since this is GSR.
However I am sharing few command output of one of the node which might be useful.
Regards
Mahesh
04-11-2011 12:34 AM
Hi everyone,
Logged tac case with cisco and as per Tac the problem could be because of Bug:CSCti75606.
Desc: Input drop counter increaing in output of show interface eventhough there is no actual drop observed.
This will be fixed in 3.9.3 version. Thanks Yogal for valuable time.
Regards
Mahesh
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide