- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-24-2011 08:23 AM - edited 03-06-2019 03:44 PM
Hello Experts ,
any idea for below drop.
#sh controllers TenGigE0/3/0/0 stats
Ingress:
Input total bytes = 184983908201609
Input good bytes = 184983908193483
Input total packets = 476570253226
Input 802.1Q frames = 0
Input pause frames = 0
Input pkts 64 bytes = 1051589535
Input pkts 65-127 bytes = 198638861313
Input pkts 128-255 bytes = 113898515084
Input pkts 256-511 bytes = 54986973113
Input pkts 512-1023 bytes = 39923316859
Input pkts 1024-1518 bytes = 41648349441
Input pkts 1519-Max bytes = 26422647884
Input good pkts = 476570253212
Input unicast pkts = 476567711194
Input multicast pkts = 2542016
Input broadcast pkts = 2
Input drop overrun = 0
Input drop abort = 0
Input drop unknown 802.1Q = 0
Input error giant = 0
Input error runt = 0Input drop other = 3920127
Input error jabbers = 0
Input error fragments = 0
Input error CRC = 12
Input error collisions = 0
Input error symbol = 0
Input error other = 2
Input MIB giant = 0
Input MIB jabber = 0
Input MIB CRC = 12
#sh interfaces TenGigE0/3/0/0
60298924302 packets input, 25287858986470 bytes, 70389 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 298092 multicast packets
0 runts, 0 giants, 0 throttles, 0 parity
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
69305800973 packets output, 29793241284072 bytes, 0 total output drops
Output 0 broadcast packets, 309639 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Regards
Mahesh
Solved! Go to Solution.
- Labels:
-
Other Switching
Accepted Solutions
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-26-2011 07:33 PM
Is this drop rate is a concern?
What is the plim type?
What's going on the other ports on that plim?
Have you tested L1?
Can u get the plim asic stat?
Sent from Cisco Technical Support iPhone App
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-25-2011 10:36 PM
Hello Guys,
Any idea ?
This is happening with almost every gig interface for node migrated to IOS-XR. But yes there is no customer complaint.
Regards
Mahesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-26-2011 07:33 PM
Is this drop rate is a concern?
What is the plim type?
What's going on the other ports on that plim?
Have you tested L1?
Can u get the plim asic stat?
Sent from Cisco Technical Support iPhone App
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-27-2011 06:37 AM
Hello Yigal,
Nice to know that you are active on community .
Well answers to your questions.
Is this drop rate is a concern?
> No. And that is the reason I did not log tac case and prefer to get answer from community.
What is the plim type?
> SPA-1X10GE-L-V2
What's going on the other ports on that plim?
> Port is admin down (Teng0/6/1)
Have you tested L1?
> Yes, 24 hour test without any issue found.
Can u get the plim asic stat?
> command (sh controllers plim asic statistics interface <>) is not working since this is GSR.
However I am sharing few command output of one of the node which might be useful.
Regards
Mahesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-11-2011 12:34 AM
Hi everyone,
Logged tac case with cisco and as per Tac the problem could be because of Bug:CSCti75606.
Desc: Input drop counter increaing in output of show interface eventhough there is no actual drop observed.
This will be fixed in 3.9.3 version. Thanks Yogal for valuable time.
Regards
Mahesh
