12-17-2014 11:00 AM - edited 03-07-2019 09:56 PM
Hi all,
Good Morning.
I am in a little project for a client, it is about connecting 2 different networks, there is the case.
Problem / facts
Proposed solution.
Inter-vlan routing
Questions.
1.- Does my switch supports the “IP Routing command” (it is necessary?)?
2.- It is necessary to configure ports on SG-200 to tag the frames for vlan 20? (I think right now they are everyone on vlan 1)
3.- Does my switch supports more than 2 SVI’s?
Example:
interface Vlan10
ip address 10.200.50.220 255.255.254.0
!
interface Vlan20
ip address 192.168.190.254 255.255.255.0
#show vlan brief
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi1/0/1, Gi1/0/2….
2 CAMARAS active Gi1/0/23 (The “trunk” one).
(Conf t)#interface GigabitEthernet1/0/23
(Conf if)#switchport mode access
(Conf if)#switchport access vlan 20
(Conf if)#spanning-tree portfast
What could be the routing?
I attach the physical topology for this case, I hope you would help me.
Thank you in advance.
Juan
:)
Solved! Go to Solution.
12-17-2014 03:14 PM
Did you enable the lanbase-routing-template? Without that, you can't enable ip routing:
switch(config)#sdm prefer lanbase-routing
And yes, these devices support ip routing. I even use it on older 2960 switches.
12-17-2014 12:19 PM
I believe the switch has to be at a certain revision before it will support ip routing. See this page http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960/software/release/12-2_55_se/configuration/guide/scg_2960/swipstatrout.html
12-17-2014 02:59 PM
Some people say that it does not support IP Routing command, some people says it does..
Look at this reference.
https://supportforums.cisco.com/discussion/11343751/can-2960-switch-support-ip-routing
They guy in that link was able to enter the command #ip routing, for intervlan routing.
I have the IOS version,
c2960s-universalk9-mz.122-55.SE7.bin
that entered Cisco features navigation, http://tools.cisco.com/ITDIT/CFN/jsp/SearchBySoftware.jsp
It says the image has IP Routing feature.
but I entered to global configuration exec mode to attempt to deploy the command, and the switch did not accept it.
SW2960S_CORE(config)#ip routing ? Global IP configuration subcommands: access-list Named access-list accounting-list Select hosts for which IP accounting information is kept accounting-threshold Sets the maximum number of accounting entries accounting-transits Sets the maximum number of transit entries address-pool Specify default IP address pooling mechanism admission Network Admission Control (NAC) alias Alias an IP address to a TCP port arp IP ARP global configuration arp IP Arp features auth-proxy Authentication Proxy default-gateway Specify default gateway (if not routing IP) device Device tracking dhcp Configure DHCP server and relay parameters dhcp-client Configure parameters for DHCP client operation dhcp-server Specify address of DHCP server to use domain IP DNS Resolver domain-list Domain name to complete unqualified host names. domain-lookup Enable IP Domain Name System hostname translation domain-name Define the default domain name finger finger server ftp FTP configuration commands gdp Router discovery mechanism gratuitous-arps Generate gratuitous ARPs for PPP/SLIP peer addresses host Add an entry to the ip hostname table host-routing Enable host-based routing (proxy ARP and redirect) hp-host Enable the HP proxy probe service http HTTP server configuration icmp ICMP options igmp IGMP global configuration local Specify local options name-server Specify address of name server to use options IP Options treatment port-map Port to application mapping (PAM) configuration commands radius RADIUS configuration commands rcmd Rcmd commands reflexive-list Reflexive access list scp Scp commands security Specify system wide security information sla IP Service Level Agreement source IP source source-route Process packets with source routing header options ssh Configure ssh options sticky-arp Allow the creation of sticky ARP entries subnet-zero Allow 'subnet zero' subnets tacacs TACACS configuration commands tcp Global TCP parameters telnet Specify telnet options tftp tftp configuration commands
Can someone verify with this exact model of switch verify if ip routing command is valid?
Thank you.
12-17-2014 03:14 PM
Did you enable the lanbase-routing-template? Without that, you can't enable ip routing:
switch(config)#sdm prefer lanbase-routing
And yes, these devices support ip routing. I even use it on older 2960 switches.
04-09-2015 10:02 AM
Thank you!
It actually worked, I created some SVI interfaces after resetting the router.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide