Hello Cisco Community, I'm hoping you can assist me...
Don't know what happen, buy my post disappeared.
I have a IR 829 router that can ping the internet
GLE-CE-02#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/34/40 ms
However when I connect any clients to the onboard lan ports they are not able to browser the internet.
I'm pretty sure I'm missing something just can't put my finger on it, any help would be greatly appreaciated.
Here is my config
GLE-CE-02#sh conf
Using 6034 out of 262144 bytes
!
! Last configuration change at 15:35:41 AEST Fri Apr 23 2021 by lcladm
! NVRAM config last updated at 15:38:47 AEST Fri Apr 23 2021 by lcladm
!
version 15.8
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service sequence-numbers
!
hostname GLE-CE-02
!
boot-start-marker
boot system flash:/ir800-universalk9-mz.SPA.158-3.M6
boot-end-marker
!
!
security authentication failure rate 3 log
security passwords min-length 6
logging userinfo
logging buffered 51200 informational
logging rate-limit all 10000
logging console informational
enable secret 5 <removed>
!
no aaa new-model
ethernet lmi global
clock timezone AEST 10 0
clock summer-time AEST recurring 1 Sun Oct 2:00 1 Sun Apr 2:00
service-module wlan-ap 0 bootimage autonomous
!
ignition off-timer 900
!
ignition undervoltage threshold 11 000
!
no ignition enable
errdisable recovery cause udld
errdisable recovery cause bpduguard
errdisable recovery cause rootguard
errdisable recovery cause pagp-flap
errdisable recovery cause dtp-flap
errdisable recovery cause link-flap
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
ip dhcp excluded-address 10.250.3.20 10.250.3.254
!
ip dhcp pool GuestOS
import all
network 10.250.3.0 255.255.255.0
default-router 10.250.3.1
dns-server 8.8.8.8 4.4.4.4
!
!
!
ip domain list <removed>
ip domain list <removed>
no ip domain lookup
ip domain name <removed>
ip name-server 10.2.0.100
ip name-server 10.2.0.20
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
!
!
chat-script lte "" "AT!CALL" TIMEOUT 20 "OK"
!
!
license udi pid IR829GW-LTE-GA-ZK9 sn <removed>
no crashinfo-deletion enable
!
!
username lcladm secret 5 <removed>
!
redundancy
!
!
!
!
!
controller Cellular 0
lte sim data-profile 1 attach-profile 1 slot 0
lte sim fast-switchover enable
lte failovertimer 5
lte modem link-recovery disable
!
!
!
!
!
!
!
!
!
!
!
interface GigabitEthernet0
no ip address
!
interface GigabitEthernet1
no ip address
duplex full
speed 1000
!
interface GigabitEthernet2
no ip address
!
interface GigabitEthernet3
no ip address
!
interface GigabitEthernet4
no ip address
!
interface Wlan-GigabitEthernet0
no ip address
!
interface GigabitEthernet5
no ip address
shutdown
duplex auto
speed auto
!
interface Cellular0
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly in
encapsulation slip
load-interval 60
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
ipv6 address autoconfig
async mode interactive
routing dynamic
!
interface Cellular1
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
load-interval 60
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer-group 1
ipv6 address autoconfig
async mode interactive
routing dynamic
!
interface wlan-ap0
no ip address
!
interface Vlan1
ip address 10.250.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
interface Async0
no ip address
encapsulation scada
!
interface Async1
no ip address
encapsulation scada
!
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip ftp source-interface Vlan1
ip tftp source-interface Vlan1
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
ip tacacs source-interface Vlan1
ip ssh version 2
!
ip radius source-interface Vlan1
logging source-interface Vlan1
dialer-list 1 protocol ipv6 permit
dialer-list 1 protocol ip permit
ipv6 ioam timestamp
!
!
snmp-server community <removed> RO
snmp-server community <removed> RW
snmp-server ifindex persist
snmp-server location <removed>
snmp-server contact <removed>
snmp-server enable traps wpan
tacacs-server directed-request
access-list 1 permit 10.250.3.0 0.0.0.255
!
control-plane
!
!
!
line con 0
session-timeout 60
exec-timeout 60 0
privilege level 15
password 7 <removed>
logging synchronous
login local
transport output telnet
stopbits 1
line 1 2
stopbits 1
line 3
script dialer lte
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
rxspeed 100000000
txspeed 50000000
line 4
no activation-character
no exec
transport preferred none
transport input all
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
line 8
no exec
transport preferred none
transport output lat pad telnet rlogin lapb-ta mop udptn v120 ssh
rxspeed 100000000
txspeed 50000000
line 1/3 1/6
transport preferred none
transport output none
stopbits 1
line vty 0 4
exec-timeout 60 0
password 7 <removed>
logging synchronous
login local
transport input telnet ssh
transport output telnet ssh
line vty 5 797
exec-timeout 60 0
password 7 <removed>
logging synchronous
login local
transport input telnet ssh
transport output telnet ssh
!
no scheduler max-task-time
ntp logging
ntp update-calendar
ntp server 127.0.0.1
no iox hdm-enable
iox client enable interface GigabitEthernet5
no iox recovery-enable
!
!
!
!
!
!
!
end
