Hi all,
i am having problem in configuring L2PT (layer 2 protocol tunneling) in my 7600 series routers.
when i am trying to configure it i am getting this issue
76a(config t)int gi2/1
76a(config-if)#service instance 1 ethe
76a(config-if)#service instance 1 ethernet
76a(config-if-srv)#encapsulation ?
% Unrecognized command
76a(config-if-srv)#encapsulation dot1q vlan 20
encapsulation dot1q vlan 20
^
% Invalid input detected at '^' marker.
is there any IOS requirement for 7600 series router to support layer 2 port channeling configuration
plz have a look at my following router information
76a#sh version
Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRISEK9-M),
Version 15.1(3)S0a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 10-Aug-11 21:09 by prod_rel_team
ROM: System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
BOOTLDR: Cisco IOS Software, c7600s72033_rp Software (c7600s72033_rp-ADVENTERPRI
SEK9-M), Version 15.1(3)S0a, RELEASE SOFTWARE (fc1)
76a uptime is 1 day, 29 minutes
Uptime for this control processor is 1 day, 29 minutes
System returned to ROM by power cycle at 17:11:32 IST Wed Feb 22 2012 (SP by po
wer on)
System restarted at 17:21:01 IST Wed Feb 22 2012
System image file is "disk0:c7600s72033-adventerprisek9-mz.151-3.S0a"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco CISCO7604 (R7000) processor (revision 2.0) with 983008K/65536K bytes of me
mory.
Processor board ID FOX101401F7
SR71000 CPU at 600MHz, Implementation 1284, Rev 1.2, 512KB L2 Cache
Last reset from power-on
1 controller (20 GigabitEthernet).
1 Virtual Ethernet interface
70 Gigabit Ethernet interfaces
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
76a#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ ----------
1 2 Supervisor Engine 720 (Active) WS-SUP720-3BXL SAL09264AQ
2 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1431PK3
3 20 ESM20G 7600-ES20-BASE JAB103501E
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ----- ------------- ------------ ------
1 0013.7f0d.5554 to 0013.7f0d.5557 4.3 8.1(3 15.1(3)S0 Ok
2 d0d0.fd64.c670 to d0d0.fd64.c69f 3.4 12.2(18r)S 15.1(3)S0 Ok
3 00e0.aabb.cc00 to 00e0.aabb.cc00 0.64 12.2(33r)SRB 15.1(3)S0 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- ------
1 Policy Feature Card 3 WS-F6K-PFC3BXL SAL09264ACZ 1.6 Ok
1 MSFC3 Daughterboard WS-SUP720 SAL092432MY 2.3 Ok
2 Centralized Forwarding Card WS-F6700-CFC SAL1431PH7S 4.1 Ok
3 ESM20G Distributed Forwardi 7600-ES20-D3CXL JAB103501B8 0.16 Ok
3/0 10XGE Port ESM-20X1GE-LINK JAB1023004A 0.17 Ok
3/1 10XGE Port ESM-20X1GE-LINK JAB1023004A 0.17 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
3/0 Pass
3/1 Pass
76a#
