memory 2811 router

[Tagir Temirgaliyev]

Hi all

I need help      

router 2811 has 2 files ios in flash

Router#sh fla

-#- --length-- -----date/time------ path

1     35202336 Mar 3 2008 16:12:28 +00:00 c2800nm-adventerprisek9-mz.124-8d.bin

...

13    59374168 Mar 5 2012 12:49:22 +00:00 c2800nm-adventerprisek9-mz.124-24.T.bin

151076864 bytes available (105431040 bytes used)

Router#

I try to make it load c2800nm-adventerprisek9-mz.124-24.T.bin

Router#sh run

..

!

boot-start-marker

boot system flash c2800nm-adventerprisek9-mz.124-24.T.bin

boot-end-marker

but after reload it shows

Router#sh ver

..

System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"

Cisco 2811 (revision 53.50) with 249856K/12288K bytes of memory.

Processor board ID FCZ12107075

11 FastEthernet interfaces

1 Virtual Private Network (VPN) Module

4 Voice FXO interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

250880K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

when loading it shows

%SYS-3-IMAGE_TOO_BIG: 'flash:c2800nm-adventerprisek9-mz.124-24.T.bin' is too lar

ge for available memory (51691544 bytes).

%SYS-6-READ_BOOTFILE_FAIL: flash:c2800nm-adventerprisek9-mz.124-24.T.bin File re

ad failed -- Not enough space.

%SYS-6-BOOT_MESSAGES: Messages above this line are from the boot loader.

boot of "c2800nm-adventerprisek9-mz.124-24.T.bin" using boot helper "flash:c2800

nm-adventerprisek9-mz.124-8d.bin" failed

error returned: File read failed -- Not enough space

loadprog: error - on file open

boot: cannot load "c2800nm-adventerprisek9-mz.124-24.T.bin"

Router#

I did

verif flash:c2800nm-adventerprisek9-mz.124-24.T.bin
it is ok

is it corrupted memory?

how to fix it?

and aslo with System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"
it dos not show voice ports for WIC2-FXO in runn conf

[Leo Laohoo]

Are you sure you want to use this IOS?

This version, 12.2(24)T is no longer available for download.  It seems that this particular IOS has been "pulled" and most likely due to highly critical bugs.

[Tagir Temirgaliyev]

not exactly this one.

I can use another one with cme 7.0

but not cme 3.3 in ios c2800nm-adventerprisek9-mz.124-8d.bin

[Joseph W. Doherty]

Disclaimer

The    Author of this posting offers the information contained within this    posting without consideration and with the reader's understanding that    there's no implied or expressed suitability or fitness for any  purpose.   Information provided is for informational purposes only and  should not   be construed as rendering professional advice of any kind.  Usage of  this  posting's information is solely at reader's own risk.

Liability Disclaimer

In    no event shall Author be liable for any damages whatsoever  (including,   without limitation, damages for loss of use, data or  profit) arising  out  of the use or inability to use the posting's  information even if  Author  has been advised of the possibility of such  damage.

Posting

It could be you have insufficient RAM to run that image.  (If you have access to Cisco's IOS images, it will tell you RAM requirements.)  (Look at how much bigger the newer IOS is in flash, and this before it's decompressed.)

If this is the case, your choices are to install extra RAM (if the platform supports more) or run an image with lower RAM requirements.  (For example, if you don't need Advance Enterprise features, a lessor feature set might use lower RAM.)

[Tagir Temirgaliyev]

problem is solved

boot system flash:c2800nm-adventerprisek9-mz.124-24.T.bin

insted of

boot system flash c2800nm-adventerprisek9-mz.124-24.T.bin