module 9 mismatch

[mahesh18]

when i do sh mod 9 on switch

sh mod 9

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

9 9 24 10/100BaseTX Ethernet WS-X5224 no ok

Module 9 mismatch of config and actual type. Ports disabled

Config: 48 port 10BaseT (Telco) , Actual: 10/100BaseTX Ethernet

Insert config module type or do a 'clear config 9'

Mod Module-Name Serial-Num

--- ------------------- --------------------

9 00018464554

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

9 00-30-b6-2a-ee-48 to 00-30-b6-2a-ee-5f 1.5 3.1(1) 5.5(15)

what does this mean?

also log shows

sh mod 9

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

9 9 24 10/100BaseTX Ethernet WS-X5224 no ok

Module 9 mismatch of config and actual type. Ports disabled

Config: 48 port 10BaseT (Telco) , Actual: 10/100BaseTX Ethernet

Insert config module type or do a 'clear config 9'

Mod Module-Name Serial-Num

--- ------------------- --------------------

9 00018464554

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

9 00-30-b6-2a-ee-48 to 00-30-b6-2a-ee-5f 1.5 3.1(1) 5.5(15)

also log shows

2008 Sep 18 17:10:35 CST -05:00 %SYS-3-MOD_CFGMISMATCH2:*Config:48 port 10BaseT (Telco)

2008 Sep 18 17:10:35 CST -05:00 %SYS-3-MOD_CFGMISMATCH3:*Actual:10/100BaseTX Ethernet

2008 Sep 18 17:10:35 CST -05:00 %SYS-3-MOD_CFGMISMATCH4:Insert config type module or do a 'clear config 8'

2008 Sep 18 17:10:37 CST -05:00 %SYS-5-MOD_OK:Module 8 is online

2008 Sep 18 17:10:52 CST -05:00 %SYS-3-MOD_CFGMISMATCH1:Module 9 configuration mismatch. Ports disabled

2008 Sep 18 17:10:52 CST -05:00 %SYS-3-MOD_CFGMISMATCH2:*Config:48 port 10BaseT (Telco)

2008 Sep 18 17:10:52 CST -05:00 %SYS-3-MOD_CFGMISMATCH3:*Actual:10/100BaseTX Ethernet

2008 Sep 18 17:10:52 CST -05:00 %SYS-3-MOD_CFGMISMATCH4:Insert config type module or do a 'clear config 9'

2008 Sep 18 17:10:55 CST -05:00 %SYS-5-MOD_OK:Module 9 is online

what does this mean?

any help?

thanks

[Mark Yeates]

Did you have a 48 port blade in the switch previously? This means that the config still reflected a 48 port blade in slot 9 and you put in a 24 port blade. Usually you will either need to reboot the switch for the config to clear out the old interface configs or issue the "clear config 9" command.

HTH,

Mark

[mahesh18]

Hi Mark

thanks for reply

i do had 48 port blade in switch previously.

so i can ran the command clear config 9 that will fix the problem?

also why all ports on module 9 show disabled?

[glen.grant]

Clear config 9 should fix it , you may have to reload the slot so it recognizes the new card correctly .

[Mark Yeates · Accepted solution]

Correct. You should remove the new blade (if already installed) and then "clear config 9". After that then install the new card and configure then new interfaces. It shows disabled because the existing configuration shows a different card installed.

HTH,

Mark