Multi vlan access ?

[oOSebBartOo]

Hi,

Im looking to access to multiple vlan.

Configuration is :

Vlan 90 : VoIP

Vlan 30 : Data

I want from my computer ( 1 interface ), acces to those both vlan.

My port configuration is :

interface GigabitEthernet1/0/18                                                                                                
description D9                                                                                                                
switchport access vlan 30                                                                                                     
switchport mode access                                                                                                        
switchport voice vlan 90                                                                                                      
switchport port-security maximum 2                                                                                            
switchport port-security                                                                                                      
switchport port-security aging time 2                                                                                         
switchport port-security violation restrict                                                                                   
switchport port-security aging type inactivity                                                                                
srr-queue bandwidth share 10 10 60 20                                                                                         
srr-queue bandwidth shape  10  0  0  0                                                                                        
queue-set 2                                                                                                                   
mls qos trust device cisco-phone                                                                                              
mls qos trust cos                                                                                                             
auto qos voip cisco-phone                                                                                                     
spanning-tree portfast                                                                                                        
spanning-tree bpduguard enable                                                                                                
!        

Thanks helping....

[oOSebBartOo]

Int trunk for interco switch ( .253 ) :

Port        Mode         Encapsulation  Status        Native vlan
Gi1/0/45    on           802.1q         trunking      99
Gi1/0/46    on           802.1q         trunking      99
Gi1/0/47    on           802.1q         trunking      1
Gi1/0/48    on           802.1q         trunking      99

Port        Vlans allowed on trunk
Gi1/0/45    1-4094
Gi1/0/46    1-4094
Gi1/0/47    43,98
Gi1/0/48    1-4094

Port        Vlans allowed and active in management domain
Gi1/0/45    1,30,43-44,90,98-99
Gi1/0/46    1,30,43-44,90,98-99
Gi1/0/47    43,98
Gi1/0/48    1,30,43-44,90,98-99

Port        Vlans in spanning tree forwarding state and not pruned
Gi1/0/45    1,30,43-44,90,98-99
Gi1/0/46    1,30,43-44,90,98-99
Gi1/0/47    43,98
Gi1/0/48    1,30,43-44,90,98-99

[sachinraja]

Hi Seb

Why do we see native vlan 99 on all trunks ? shouldnt it be vlan 90 ? and what is gig 1/0/47 on .253 switch ? i do not see both data and voice vlans on that trunk ?

Raj

[oOSebBartOo]

Hi,

Vlan 99 is an "old" vlan, that is not use actually.

Interface  gig 1/0/47 is an other lan on a different localisation ( fiberchannel connexion ), so this one don't need to have voice or data vlan.

Seb

[sachinraja]

Hi Seb

Can you change the native vlan to VLAN 90 (instead of 99) on all uplink ports and then try pinging this ?

Also, your edge switches are layer 2 in nature, right ? are you sure you pointed the default gateway to the core switch , and not the access ?

Raj

[oOSebBartOo]

Ok i will try to  modify vlan to 90 on all.

Yes i'm sure for core switch, .252 that you have seen was a copy / paste mistake

I don't understand what you mean with "your edge switches are layer 2 in nature, right" ?

[sachinraja]

Hi seb

i just meant that the layer 3 routing should be performed only at one place, which will be the aggregation switch .. on your interconnect switches, you should do layer 2 switching, with vlans configured etc.. all default gateway should point to your aggregation switch, where you define multiple vlans for routing...

Hope this helps..

Raj

[oOSebBartOo]

Ok i'll try, on switch .252 i set default gateway himself so, right?