Solved: Re: N7K Type-2 consistency

alanjbrown · ‎02-10-2011

Can anyone tell me what this incompatible message means, impact and how to resolve ?

Version: n7000-s1-dk9.4.2.4.bin

MYN7K# show vpc brief
Legend:
(*) - local vPC is down, forwarding via vPC peer-link

vPC domain id                            : 20
Peer status                               : peer adjacency formed ok
vPC keep-alive status                 : peer is alive
Configuration consistency status: success
Type-2 consistency status         : failed
Type-2 consistency reason        : SVI type-2 configuration incompatible

thanks,

Al

Chad Peterson · ‎02-10-2011

Hi Al,

Can you send "show vpc consistency-parameters global". Type-2 error like this should refer to a configuration mismatch. Likely you are either missing an SVI on 1 switch, or an SVI is in a down state on one where other is up.

Chad

View solution in original post

Chad Peterson · ‎02-10-2011

Hi Al,

Can you send "show vpc consistency-parameters global". Type-2 error like this should refer to a configuration mismatch. Likely you are either missing an SVI on 1 switch, or an SVI is in a down state on one where other is up.

Chad

alanjbrown · ‎02-11-2011

Chad,

As requested:

MYN7Kr1# show vpc consistency-parameters global

Legend:
Type 1 : vPC will be suspended in case of mismatch

Name                        Type Local Value            Peer Value
-------------               ---- ---------------------- -----------------------
STP Mode                    1     Rapid-PVST             Rapid-PVST
STP Disabled                1     None                   None
STP MST Region Name         1     ""                     ""
STP MST Region Revision     1     0                      0
STP MST Region Instance to 1
VLAN Mapping
STP Loopguard               1     Disabled               Disabled
STP Bridge Assurance        1     Enabled                Enabled
STP Port Type, Edge         1     Normal, Disabled,      Normal, Disabled,
BPDUFilter, Edge BPDUGuard        Disabled               Disabled
STP MST Simulate PVST       1     Enabled                Enabled
Interface-vlan admin up     2     101-103,115-116,130-13 100-103,115-116,130-13
                                  5,140-142,145-146,150- 5,140-142,145-146,150-
                                  153,160,165,170,175,18 153,160,165,170,175,18
                                  0,190-197,201,241,400- 0,190-197,201,241,400-
                                  407,420,997            407,420,997
Allowed VLANs               -     1,100-104,115-116,130- 1,100-104,115-116,130-
                                  135,140-142,145-146,15 135,140-142,145-146,15
                                  0-153,160,165,170,175, 0-153,160,165,170,175,
                                  180,190-197,200-201,24 180,190-197,200-201,24
                                  1,302,400-407,420,500- 1,302,400-407,420,500-
                                  504,997,999            504,997,999
Local suspended VLANs       -     -                      -

Sorry about the format!

The only difference is the Vlans 100 and 101

MYN7Kr1# show int vlan 100
Vlan100 is administratively down, line protocol is down

MYN7Kr1# show int vlan 101
Vlan101 is up, line protocol is up

MYN7Kr2# show int vlan 100
Vlan100 is up, line protocol is up

MYN7Kr2# show int vlan 101
Vlan101 is up, line protocol is up

If we enable the Vlan 100 then we have had some routing issues so it has remained shutdown with everthing working. So that's probably the cause but is it important and does it affect my network that we are in this inconsistency state?

thks

Al

mstyszynski · ‎02-15-2011

hello Alan ,

I have remarked the same issue when I was adding some new VLAN-ids to the VPC config and then configured the SVIs on top of it.

The missing SVIs are only the VL226 and VL126 from the VPC point of view ( i.e. configured only on one of the peer VPC switches ), even if we still have other SVIs ( VL100 and VL200 ) that are enabled on one of the peer vpc switches. We can note also that in terms of the forwording it works fine. If you want to establish OSPF adjacency with the 3rd party switch-router then the adjacency will also come up ( at least in the 5.1.2 NX-OS ) .

Cheers ,

Michal

##########################################################################################

NX7K-2-edge-2-2# sh vpc consistency-parameters global

Legend:

Type 1 : vPC will be suspended in case of mismatch

Name Type Local Value Peer Value

------------- ---- ---------------------- -----------------------

STP Mode 1 Rapid-PVST Rapid-PVST

STP Disabled 1 None None

STP MST Region Name 1 "" ""

STP MST Region Revision 1 0 0

STP MST Region Instance to 1

VLAN Mapping

STP Loopguard 1 Disabled Disabled

STP Bridge Assurance 1 Disabled Disabled

STP Port Type, Edge 1 Normal, Disabled, Normal, Disabled,

BPDUFilter, Edge BPDUGuard Disabled Disabled

STP MST Simulate PVST 1 Enabled Enabled

Interface-vlan admin up 2 100,122,200,226 100,122,126,200

Interface-vlan routing 2 100,122,200,226 100,122,126,200

capability

Allowed VLANs - 100,122,126,200,226,30 100,122,126,200,226,30

0 0

Local suspended VLANs - - -

NX7K-2-edge-2-2#

NX7K-2-edge-2-2# sh ip int brief

IP Interface Status for VRF "default"(1)

Interface IP Address Interface Status

Vlan100 100.100.100.22 protocol-up/link-up/admin-up

Vlan122 122.122.122.22 protocol-up/link-up/admin-up

Vlan226 26.26.26.22 protocol-up/link-up/admin-up

NX7K-2-edge-2-2#

NX7K-1-edge-1-2(config)# sh vpc consistency-parameters global

Legend:

Type 1 : vPC will be suspended in case of mismatch

Name Type Local Value Peer Value

------------- ---- ---------------------- -----------------------

STP Mode 1 Rapid-PVST Rapid-PVST

STP Disabled 1 None None

STP MST Region Name 1 "" ""

STP MST Region Revision 1 0 0

STP MST Region Instance to 1

VLAN Mapping

STP Loopguard 1 Disabled Disabled

STP Bridge Assurance 1 Disabled Disabled

STP Port Type, Edge 1 Normal, Disabled, Normal, Disabled,

BPDUFilter, Edge BPDUGuard Disabled Disabled

STP MST Simulate PVST 1 Enabled Enabled

Interface-vlan admin up 2 100,122,126,200 100,122,200,226

Interface-vlan routing 2 100,122,126,200 100,122,200,226

capability

Allowed VLANs - 100,122,126,200,226,30 100,122,126,200,226,30

0 0

Local suspended VLANs - - -

NX7K-1-edge-1-2(config)# sh ip int brief

IP Interface Status for VRF "default"(1)

Interface IP Address Interface Status

Vlan122 122.122.122.12 protocol-up/link-up/admin-up

Vlan126 126.126.126.12 protocol-up/link-up/admin-up

Vlan200 200.200.200.12 protocol-up/link-up/admin-up

NX7K-1-edge-1-2(config)#

alanjbrown · ‎03-04-2011

Chad,

Thanks for the help. We just match the SVI status the same on both vPC peers and everything resolved.

MYN7Kr2# show vpc brief

Legend:

(*) - local vPC is down, forwarding via vPC peer-link

vPC domain id : 20

Peer status : peer adjacency formed ok

vPC keep-alive status : peer is alive

Configuration consistency status: success

Type-2 consistency status : success

vPC role : secondary

Number of vPCs configured : 6

Peer Gateway : Disabled

thks

ank.narang · ‎08-30-2012

Hi All,

one quick question. May be its related this post.

We have 2 box with VPC config N5K (5.0) . we are planning to add Vlan on box. what is best practice for this.is there any thing break when we add on one box. and then other. in time between do we find any abnormal behaviour in switch ?

Thanks & Regards

A.N