cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2245
Views
0
Helpful
4
Replies

Nexus 7710 with F3 1/10G not suport GLC-T

patcbr600
Beginner
Beginner

 

 

Hi all,

 

Hi have a nexus 7710 with F3 48x1/10G interfaces but i'm not able to configure a interface with GLC-T, the switch does not let to configure speed to 1000 and givs the following error:

 

Ethernet7/14
    transceiver is present
    type is 1000base-T
    name is CISCO-AVAGO     
    part number is ABCU-5710RZ-CS4
    revision is B2  
    serial number is AGM1714226D     
    nominal bitrate is 1300 MBit/sec
    Link length supported for copper is 100 m
    cisco id is --
    cisco extended id number is 4

Ethernet7/14
  Model:                 N77-F348XP-23
  Type (SFP capable):    1000base-T
  Speed:                 10000
  Duplex:                full
  Trunk encap. type:     802.1Q
  FabricPath capable:    yes
  Channel:               yes
  Broadcast suppression: percentage(0-100)
  Flowcontrol:           rx-(off/on),tx-(off/on)
  Rate mode:             dedicated
  Port mode:             Routed,Switched
  QOS scheduling:        rx-(8q4t),tx-(3p5q1t)
  CoS rewrite:           yes
  ToS rewrite:           yes
  SPAN:                  yes
  UDLD:                  yes
  MDIX:                  no
  TDR capable:           no
  Link Debounce:         yes
  Link Debounce Time:    yes
  FEX Fabric:            yes
  dot1Q-tunnel mode:     yes
  EFP:                   no
  Num Rewrites Allowed:  104
  Pvlan Trunk capable:   yes
  Port Group Members:    9-16
  EEE (efficient-eth):   no
  PFC capable:           yes
  Breakout capable:      no

 interface ethernet 7/14
 speed 1000
ERROR: Ethernet7/14: Configuration does not match the port capability.

 

Can anyone give a help on this, in the cco the GLC-T is supported.

 

Thanks

Patcbr600

 

 

4 Replies 4

Steve Fuller
Engager
Engager

Hi,

According to the Limitations section of the NX-OS 6.2 release notes, this is not supported:

N77-F348XP-23: 1 Gigabit Ethernet Not Supported
On the Cisco Nexus 7700 48-port 1/10-Gigabit Ethernet SFP+ I/O module (N77-F348XP-23), 1 Gigabit Ethernet port speed is not supported on the F3 Series modules in Cisco Nexus Release 6.2(6).

I don't think the wording is very clear, but the way I read this is that it's a software limitation that will change in later releases. Especially as it would be a pretty useless 1/10 GE module if it didn't support 1GE.

Regards

1G is supported with software release 6.2.8:

http://www.cisco.com/c/en/us/td/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.html#76711

 

sean_evershed
Rising star
Rising star

Try removing the SFP, set the speed and then re-insert it.

cdtomkins
Beginner
Beginner

Hi,


Did you ever resolve this? I will have this deployment scenario in a few months' time.


Thanks

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers