No Ping ...!!!!!! from Switch

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-07-2017 11:34 PM - edited 03-08-2019 10:07 AM
Hi All,
I have an issue with one of my switch ( 4500 series) .
Actual Scenario:
--------------------
We have a server which has two interfaces and each assigned with an IP address ( in the range[10.49.8.132/27]) . Eth0 IP:10.49.8.135 and Eth1 IP:10.49.8.136 . Eth0 is connected to Switch-A and Eth-1 is connected to Switch-B . When tried to ping Eth0 IP it is success from switch-A whereas Eth-1 is not a success. Now the same IP's are pingable from the other switch-B . I am not sure what might be wrong . Please advise .
Thanks,
Babjani.
- Labels:
-
Other Switching
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-07-2017 11:46 PM
Hi,
Can you please share your configurations. are you using any vlans in this switches
or default you are using ?
thanks
CRaju
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-09-2017 04:17 AM
Hi Raju ,
Yes , we have vlans on both the switches . Here are the config files attached.
Thanks,
Babjani
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-11-2017 10:51 AM
Hi
I checked the config.. files looks good .
could you please give a try .
default gateway for your system to use Switch virtual interface NOT HSRP Virtual ip address
I hope you understand my question . .
this is my mobile number 91+9618613678
Thanks
CRaju
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-12-2017 03:36 AM
HI
As I discussed.
If it is possible to try to upgrade your IOS Version to latest .
because both version are different .
cat4500-ipbasek9-mz.150-2.SG5.bin
cat4000-i9k91s-mz.122-25.EWA5.bin
1.https://software.cisco.com/download/release.html?mdfid=279320804&softwareid=280805680&release=12.2.25-EWA&rellifecycle=ED&relind=DEFERRED&reltype=deferred/
2.https://software.cisco.com/download/release.html?mdfid=279636820&softwareid=280805680&release=15.0.2-SG5
Thanks
CRaju
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-12-2017 10:28 PM
Thank you Raju , will give it a try .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-09-2017 06:50 PM
Hi
Your config looks fine, from what external source are you trying to ping it? is the 2nd NIC on the server configured with a gateway?
If they are on the same subnet they will be able to ping each other without gateway configured on the NICs.
>> Marcar como útil o contestado, si la respuesta resolvió la duda, esto ayuda a futuras consultas de otros miembros de la comunidad. <<
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-09-2017 07:24 PM
Hi Julio ,
Yes they are on the same subnet . Eth0 IP:10.49.8.135/27 and Eth1 IP:10.49.8.136/27 as mentioned earlier in the discussion .
Thanks,
Babjani
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-09-2017 10:00 PM
Thank you, But Im referring if both NICs are configured with the gateway:
10.49.8.134
>> Marcar como útil o contestado, si la respuesta resolvió la duda, esto ayuda a futuras consultas de otros miembros de la comunidad. <<
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-09-2017 11:36 PM
Hi Julio,
Yes ,both the servers are using the standby IP of HSRP as their gateway. I am pinging it from the switches only and not from any other source .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-13-2017 12:55 AM
Hello
These switches seemed to be separate and not stacked or visualized
In a virtual stack link aggregation can span two switches as the server will see it a just one switch, However if the switch isnt "stacked" then the server connections need to be on the same switch in a link aggregation setup.(LACP) which I also don't see in you configuration.
I cannot comment on your server and its teaming software but having a server connected to two separate switches sharing the same address range and default-gateway and without any aggregation setup isnt really feasible.
res
Paul
Please rate and mark as an accepted solution if you have found any of the information provided useful.
This then could assist others on these forums to find a valuable answer and broadens the community’s global network.
Kind Regards
Paul
