cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1502
Views
0
Helpful
3
Replies

PFC enabled? show queuing interface - Per-priority-pause status

nermushermus
Level 1
Level 1

Hello,

On the Nexus 5596 I have the following configured for the port (no lldp transmit and receive) due to iSCSI TLV not supported by Nexus (at the moment):

interface Ethernet1/21

  no lldp transmit

  no lldp receive

  switchport access vlan xx

  flowcontrol receive on

  flowcontrol send on

  channel-group x

However under show queuing interface I see Tx active for Per-priority-pause status:

Ethernet1/21 queuing information:

  TX Queuing

    qos-group  sched-type  oper-bandwidth

        0       WRR              5

        3       WRR             95

  RX Queuing

    qos-group 0

    q-size: 350080, HW MTU: 1500 (1500 configured)

    drop-type: drop, xon: 0, xoff: 350080

    Statistics:

        Pkts received over the port             : 0

        Ucast pkts sent to the cross-bar        : 0

        Mcast pkts sent to the cross-bar        : 0

        Ucast pkts received from the cross-bar  : 0

        Pkts sent to the port                   : 0

        Pkts discarded on ingress               : 0

        Per-priority-pause status               : Rx (Inactive), Tx (Inactive)

    qos-group 3

    q-size: 90240, HW MTU: 9216 (9216 configured)

    drop-type: no-drop, xon: 17280, xoff: 37120

    Statistics:

        Pkts received over the port             : 328665922

        Ucast pkts sent to the cross-bar        : 328665646

        Mcast pkts sent to the cross-bar        : 231

        Ucast pkts received from the cross-bar  : 356032494

        Pkts sent to the port                   : 356032384

        Pkts discarded on ingress               : 0

        Per-priority-pause status               : Rx (Inactive), Tx (Active)

Am I missing something?

Thank you

3 Replies 3

ansverma
Cisco Employee
Cisco Employee

Hi,

can you share show lldp interface

Also try to bounce the lldp feature.

Thanks

Anshul

Thanks Anshul,

Does the "Per-priority-pause status: Rx (Inactive), Tx (Active)" mean PFC is Tx enabled?  This is an iSCSI setup and as I understand it, Nexus does not support the iSCSI TLV for DCB at this time.  We would certainly want to disable this PFC if it is enabled, but if this will not cause issues then we can overlook it.

I only have the show tech-support currently, but I have requested the output of the command you requested.  Would the following suffice?  It shows Tx and Rx disabled, however the interface is receiving DCBX frames.  I will post the output of the requested as soon as I receive it.

`show lldp dcbx interface Ethernet1/21 `


Local DCBXP Control information:
Operation version: 00  Max version: 00  Seq no: 1  Ack no: 0
Type/
Subtype    Version    En/Will/Adv Config
003/000     000        Y/N/Y      1008
004/000     000        Y/N/Y      8906001b21 08
002/000     000        Y/N/Y      0000100064 00000000 00000002
`show system internal dcbx info interface Ethernet1/21 `

Interface info for if_index: 0x1a014000(Eth1/21)
tx_enabled: FALSE
rx_enabled: FALSE
dcbx_enabled: FALSE
DCX Protocol: CEE
DCX CEE NIV extension: disabled


Port MAC address:  00:05:73:e5:42:9c


DCX Control FSM Variables: seq_no: 0x1, ack_no: 0x0,my_ack_no: 0x0, peer_seq_no: 0x0 oper_version: 0x0,  max_version: 0x0 fast_retries 0x0

Lock Status: UNLOCKED
PORT STATE: UP
LLDP Neighbors

No DCX tlvs from the remote peer

6 Features on this intf for Protocol DCX CIN(0)

Feature type PFC (3)
feature type 3(DCX CIN-PFC)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 0
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 1 data bytes:10

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type LLS (6)sub_type FCoE Logical Link Status (0)
feature type 6(DCX CIN-LLS)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 0
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x1d9

Desired config cfg length: 1 data bytes:00

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type App (5)sub_type FCoE iSCSI (0)
feature type 5(DCX CIN-App)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 1
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 1 data bytes:08

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type PriMtu (8)
feature type 8(DCX CIN-PriMtu)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 1
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 16 data bytes:05    dc    05    dc    05    dc    05    dc    24    00    05    dc    05    dc    05    dc

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type PriGrp (2)
feature type 2(DCX CIN-PriGrp)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 1
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 24 data bytes:64    00    00    00    00    00    00    00    00    0f    00    0f    00    0e    00    0e    20    64    00    0e    00    0e    00    0e

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type LLS (6)sub_type LAN Logical Link Status (1)
feature type 6(DCX CIN-LLS)sub_type 1
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 1
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0xaf

Desired config cfg length: 1 data bytes:80

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


3 Features on this intf for Protocol DCX CEE(1)

Feature type PFC (3)
feature type 3(DCX CEE-PFC)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 0
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 2 data bytes:10    08

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type App (4)sub_type FCoE iSCSI (0)
feature type 4(DCX CEE-App)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 1
     remote_tlv_not_present_notification_sent 1
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 6 data bytes:89    06    00    1b    21    08

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Feature type PriGrp (2)
feature type 2(DCX CEE-PriGrp)sub_type 0
Feature State Variables: oper_version 0 error 0 local error 0 oper_mode 0
     feature_seq_no 0 remote_feature_tlv_present 0 remote_tlv_aged_out 0
     remote_tlv_not_present_notification_sent 0
Feature Register Params: max_version 0, enable 1, willing 0 advertise 1
     disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 13 data bytes:00    00    10    00    64    00    00    00    00    00    00    00    02

Operating config cfg length: 0 data bytes:

Peer config cfg length: 0 data bytes:


Features on this intf for LLDP

lldp feature type 2(PriMtu)sub_type 0
lldp feature register params max_version 0, enable 1, willing 0 advertise 1, disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0x179

Desired config cfg length: 16 data bytes:05    dc    05    dc    05    dc    05    dc    24    00    05    dc    05    dc    05    dc

Peer config cfg length: 0 data bytes:

lldp feature type 1(LLS)sub_type 1
lldp feature register params max_version 0, enable 1, willing 0 advertise 1, disruptive_error 0 mts_addr_node 0x101 mts_addr_sap 0xaf

Desired config cfg length: 1 data bytes:01

Peer config cfg length: 0 data bytes:

Traffic Counters
DCBX pkt stats:

    Total frames out: 61083
    Total Entries aged: 17
    Total frames in: 60613
    DCBX frames in: 60318
    Total frames received in error: 0
    Total frames discarded: 0
    Total TLVs unrecognized: 0

Here is the output of the requested command:

Switch1-5596# show lldp interface ether1/21

Interface Information:

  Enable (tx/rx/dcbx): N/N/N    Port Mac address: 00:05:73:e5:42:9c