Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi ,in switch 2960s ( c2960s-universalk9-mz.122-55.SE5 ) , i want to marking the trafic between two hosts ( Data replication ), i choose to use " mac access-list"  to classify my trafic before apply the policy marking . but did'nt work . can you help...

As you can see from the following command I get the information for one port.C2960s-48fps-01#show int gi1/0/6 | include Last | protoGigabitEthernet1/0/6 is down, line protocol is down (notconnect)  Last input never, output 1w6d, output hang never  La...

techbjs08 by Level 1
  • 24455 Views
  • 2 replies
  • 0 Helpful votes

Good Day,Fighting an issue with DHCP from the service provider. Just not getting it.So I have  a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data.I have this route...

mtnchaser by Level 1
  • 889 Views
  • 4 replies
  • 0 Helpful votes

I have been looking at a solution for a customer. they have 2 access switches (3560) and 2 core switches (2960). they also have 2 routers for Wan access, configured with HSRP.rtr 1 192.168.88.20   rtr2 192.168.88.21     Virtual adddress 192.168.88.10...

pcromwell by Level 3
  • 658 Views
  • 6 replies
  • 0 Helpful votes

I can configure at a Cisco Router two default routes:ip route 0.0.0.0 0.0.0.0 fastethernet 0/0ip route 0.0.0.0 0.0.0.0 fastethernet 0/1Both appeaers in "sh run". Both appears in "sh ip route".But what is the result of this config? is the second route...

HiI'm looking to build out a small core for a remote office dc. The dc is just a couple of racks with 2 server switches, 2 desktop switches, and a couple of firewalls. A handful of circuits will also drop in. My initial thought is a 4948 as it has ad...

Hi All,I have two 6509s with a single CSM in each set up for FT.  No changes have been made to the configuration recently but I have noticed the following EMs occuring in the logs.  Both logs are from the same period of time so you can see what is ha...

      Hi TeamWe are running nexus 5018 in our DC.I have one samll question, Please any one can help me.What is the difference betwen "channel-group 214 mode active"  and " channel-group 216"Any difference?.. because i have problem with this config we...

I wonder how to configure Paramenters QOS ( COS 6 and DCSP 46 )in a switch Cisco 2960.Below is the current configuration of the interfaces :| Interface GigabitEthernet1/0/5switchport mode accessswitchport access vlan 2 switchport voice vlan 11srr-qu...

brpeixoto by Level 1
  • 406 Views
  • 1 replies
  • 0 Helpful votes

Hello Everybody,I have an issue with the device in subject.I need that some server, listed as service on CSS, can contact a content VIP on the same subnet......To allow that traffic I configured grouping on CSS (group 1) with vip address and an ACL t...

HiI wounder if there is any way to ping the local deviceses connected to a network hosted by a Cisco 1921 router? I wan't to be able to ping the device(computer name) but currently cant do that.for example if a device is named "cisco-router" then I w...

Hi,Does anyone know what is mean the field below :  Misdirected Packets                          Switch#sh ip dhcp snooping statistics detail Packets Processed by DHCP Snooping                    = 1212 Packets Dropped Because    IDB not known      ...

I have a Cisco 1921 Router, a Cisco Catalyst 2960 and a Cisco Catalyst 2970 and I want the router to be able to assign ip-addresses by what VLAN a device is active on.VLAN1: 10.0.0.0/24VLAN2: 10.0.1.0/24The router is connected to the Catalyst 2960 an...

Review Cisco Networking for a $25 gift card