01-09-2024 03:25 AM
Hello All,
I am facing some PoE issues in Cisco 9300, I wonder if anyone has experienced the same?
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 65 C9300-48P 17.06.03 CAT9K_IOSXE INSTALL
Jan 9 10:32:19.718: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/9: Power given, but State Machine Power Good wait timer timed out
Jan 9 10:32:23.725: ILP:: Gi1/0/9: State=NGWC_ILP_BAD_POWER_S-9, Event=NGWC_ILP_WAIT_LINK_DOWN_TIMER_EV-42
Jan 9 10:32:29.718: ILP:: Gi1/0/9: State=NGWC_ILP_BAD_POWER_S-9, Event=NGWC_ILP_WAIT_BAD_PWR_TIMER_EV-51
Jan 9 10:32:29.719: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
Jan 9 11:12:31.699: ILP:: ILP:Gi1/0/2:power real 1578, min 845, max 2593, police 0, overdraw: 0
Jan 9 11:12:31.699: ILP:: ILP:Gi1/0/3:power real 1578, min 845, max 2593, police 0, overdraw: 0
Jan 9 11:12:31.699: ILP:: ILP:Gi1/0/9:power real 0, min 0, max 0, police 0, overdraw: 0
Jan 9 11:12:31.699: ILP:: ILP:Gi1/0/11:power real 2644, min 2362, max 4331, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/12:power real 3262, min 2250, max 3375, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/13:power real 1575, min 843, max 2587, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/14:power real 1631, min 843, max 2587, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/23:power real 1576, min 844, max 2589, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/27:power real 1581, min 846, max 2597, police 0, overdraw: 0
Jan 9 11:12:31.700: ILP:: ILP:Gi1/0/28:power real 3275, min 2428, max 3387, police 0, overdraw: 0
#sh power inline gigabitEthernet 1/0/9
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/9 auto on 15.4 Cisco PD n/a 30.0
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 472.0 132.6 339.4
01-10-2024 05:22 PM
End device is the Polycom Handset
suggest to configured LLDP see if that can resolve the issue.
01-11-2024 01:28 AM
Hi, lldp is enabled on switch already
Global LLDP Information:
Status: ACTIVE
LLDP advertisements are sent every 30 seconds
LLDP hold time advertised is 120 seconds
LLDP interface reinitialisation delay is 2 seconds
01-11-2024 08:58 AM
i would suggest to read some troubleshoting steps :
what is the model polycom device ?
01-11-2024 09:40 AM
Jan 11 17:36:30.234: LLDP advertisement packet TX'd on intf GigabitEthernet1/0/23
Jan 11 17:36:31.157: %ILPOWER-5-IEEE_DISCONNECT: Interface Gi1/0/9: PD removed
Jan 11 17:36:31.417: LLDP advertisement packet TX'd on intf GigabitEthernet1/0/27
Jan 11 17:36:31.755: LLDP advertisement packet RX'd on intf GigabitEthernet1/0/13
Jan 11 17:36:31.755: Peer lldp frame rcvd from Src MAC address :48:25:67:16:C2:AB
Jan 11 17:36:31.872: LLDP advertisement packet RX'd on intf GigabitEthernet1/0/2
Jan 11 17:36:31.873: Peer lldp frame rcvd from Src MAC address :48:25:67:AE:5A:B9
Jan 11 17:36:31.995: LLDP advertisement packet TX'd on intf GigabitEthernet1/0/3
Jan 11 17:36:33.327: LLDP advertisement packet TX'd on intf GigabitEthernet1/0/13
Jan 11 17:36:36.377: LLDP advertisement packet RX'd on intf GigabitEthernet1/0/3
Jan 11 17:36:36.377: Peer lldp frame rcvd from Src MAC address :48:25:67:16:C1:27
Jan 11 17:36:38.348: LLDP advertisement packet RX'd on intf GigabitEthernet1/0/27
Jan 11 17:36:38.349: Peer lldp frame rcvd from Src MAC address :48:25:67:AE:5A:5A
All other ports seems ok but only this one
The issue is last time when we removed phone from port and try to connect on another, it didn't work
And there are two more ports where when we unplugged the phone and plug back in, they didn't come up but in logs at least no errors like port 9 (they are port11 and 14)
01-11-2024 10:28 AM
show interface status <<- check if the port is errdisable
MHM
01-11-2024 10:56 AM
Gi1/0/9 *** User Port *** notconnect 60 auto auto 10/100/1000BaseTX
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide