07-24-2012 04:30 AM - edited 03-07-2019 07:56 AM
hi ,
im using qos
here is my config
##########################
class-map match-all wireless
match access-group name wireless
!
policy-map wireless
class wireless
bandwidth 15000
class class-default
fair-queue
!
! ############################
as u see, im using qos to gurantee 15 mega for users of the access-list wireless
in the same time i want the traffic not to exceed 16 mega ,
i just want to give 15 gurantee , and up to 16 if aviable
im trying to type the command
police 160000 exceed-action drop
but the ios is not accepting it ,
im wondering how to type it and limit the bw up to 16 mega ???
here is the outut when i try to type it
$$$$$$$$$$$$$$$$$$$$$$$$$$
Gateway2(config-pmap-c)#police 16000 ?
<500-512000000> Burst bytes
bc Conform burst
conform-action action when rate is less than conform burst
pir Peak Information Rate
<cr>
Gateway2(config-pmap-c)#police 16000
$$$$$$$$$$$$$$$$$$$$
as u see there is no exceed-action but instead , there is
conform-action
=====================
regards
Solved! Go to Solution.
07-24-2012 06:21 AM
here you can find full examples for the 7600 series.
Please rate if you believe i have been helpful
Alessio
07-24-2012 04:34 AM
policy conform-action transmit exceed-action drop...
conform first!
HTH
Alessio
07-24-2012 04:36 AM
hi ,
should i type the command
police 15000 conform-action transmit exceed-action drop
or
police 16000 conform-action transmit exceed-action drop
i just want to gurantee 15 , and give upto 16 if avaibale
regards
07-24-2012 04:34 AM
Under your police command, specify a conform action and then your exceed action should be available.
HTH,
John
07-24-2012 04:39 AM
hi , wt should i give a value to confim action ?
should i give it the gurantee bw ???
in this case , does the command bandwith id needed ??
regards
07-24-2012 04:47 AM
؟؟؟؟؟؟؟؟؟؟
07-24-2012 04:54 AM
Hi Ahmed,
please do not mix garanteed bandwidth with policing.
http://www.cisco.com/en/US/docs/ios/qos/command/reference/qos_n1.html#wp1047146
Please read the usage of this command aand especially the usage guidelines in this doc.
Alessio
07-24-2012 05:04 AM
hi ,
after all of that ,
the command is not being accepted
bandwidth command is not supported in input direction for this interface
Gateway2(config-if)#service-policy output wireless
bandwidth command is not supported in output direction for this interface
Configuration failed on GigabitEthernet1/1
Gateway2(config-if)#service-policy output wireless
*Jul 24 11:18:45.650: %QOS-6-POLICY_INST_FAILED:
Service policy installation failed
Gateway2(config-if)#service-policy input wireless
bandwidth command is not supported in input direction for this interface
Configuration failed on GigabitEthernet1/1
Gateway2(config-if)#
Gateway2(config-if)#
neither output nor input !!!!!!!!!!
07-24-2012 05:23 AM
i guess you nee to remove the bandwidth command first. and then to re-apply it in the direction you need
send the qos/interface config if you can
Alessio
07-24-2012 05:39 AM
hi ,
i removed the bandwith command
and again another problem
$$$$$$$$$$$$$$$$$$$$$$
Gateway2(config-if)#service-policy output wirless
% policy map wirless not configured
Gateway2(config-if)#service-policy output wireless
fair-queue command is not supported in output direction for this interface
Configuration failed on GigabitEthernet1/9
Gateway2(config-if)#
$$$$$$$$$$$$$$$$$$$$$$$4
my ios is
"sup-bootdisk:c7600s3223-adventerprisek9-mz.152-1.S.bin"
my router is 7640
im wondering if my router accept QOS ??????/
regards
07-24-2012 05:45 AM
the config is so simple
class-map match-all wireless
match access-group name wireless
!
policy-map wireless
class wireless
class class-default
fair-queue
!
ip access-list extended wireless
permit ip xx.xx.66.128 0.0.0.127 any
regards
07-24-2012 05:48 AM
Yes,
i think that you need to take away fair-queue and to leave the default FIFO on class-default.
Alessio
07-24-2012 05:56 AM
it accepted it after removing fair queue
but now , im wondering ,
i removed fair queue and bandwith commands , and asking if the qos has benefit ????
i mean wt should i do to gurantee 15 mega bw for the acceslist wireless ??????
regrads
07-24-2012 06:02 AM
hi , i made another policaymap and the same issue appeared !!!
here is new config
@@@@@@@@@@@@@@@@@@@@
!
class-map match-all AlessioAndreoli
match access-group name wireless
!
policy-map AlessioAndreoli
class AlessioAndreoli
bandwidth 15000
@@@@@@@@@@@@@@@@@@@@
and here is the output :
Gateway2(config-if)#service-policy output AlessioAndreoli
bandwidth command is not supported in output direction for this interface
Configuration failed on GigabitEthernet1/9
Gateway2(config-if)#service-policy input AlessioAndreoli
bandwidth command is not supported in input direction for this interface
Configuration failed on GigabitEthernet1/9
Gateway2(config-if)#
as you see, it cant be applied niether in nor out
!!!!!!!!!!!!!!!!!!!!11
07-24-2012 06:09 AM
hi ,
assume im not expert in policying and qos and that what i am.
i just want to gurentee 15 meg for the access-list users , and dont want them to exceed any more bandwih
my goal is to "" Gurantee bw , Dont allow exceed this bw""""
now ,
forget qos and policying
now wt i need to do in config to achive my goal ??
could u give me a breif config of wt i need .
regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide