09-24-2014 10:53 PM - edited 03-07-2019 08:52 PM
Hi Team
We happen case GLC-T with Catalyst 2960 Hang , It can't work
We was reload switch but same ( GLC-T with Catalyst 2960 Hang)
and use command bellow
Switch97#
Switch97#
Switch97#sh int gi 1/0/26 transceiver 5 transceiver de
Switch97#sh int gi 1/0/25 transceiver detail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
Switch97#
Switch97#
Switch97#sh int gi 1/0/25 transceiver detail 6 transceiver de
Switch97#sh int gi 1/0/26 transceiver detail
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
We try IOS Software EX3, EX4, EX5 and 15-2.2 but can't problem
Please suggest case to me
09-24-2014 11:21 PM
Catalyst 2960S-48FPS-L |
|
09-24-2014 11:26 PM
cisco WS-C2960X-24TS-L (APM86XXX) processor (revision A0) with 524288K bytes of memory.
Processor board ID FCW1832A38M
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
28 Gigabit Ethernet interfaces
The password-recovery mechanism is enabled.
512K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address : F0:9E:63:F7:8B:00
Motherboard assembly number : 73-15973-02
Power supply part number : 341-0529-02
Motherboard serial number : FOC183234M6
Power supply serial number : LIT18220612
Model revision number : A0
Motherboard revision number : A0
Model number : WS-C2960X-24TS-L
Daughterboard assembly number : 73-14200-03
Daughterboard serial number : FOC18319MMY
System serial number : FCW1832A38M
Top Assembly Part Number : 800-41470-01
Top Assembly Revision Number : A0
Version ID : V03
CLEI Code Number : CMMMU00ARB
Daughterboard revision number : A0
Hardware Board Revision Number : 0x12
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 28 WS-C2960X-24TS-L 15.0(2)EX3 C2960X-UNIVERSALK9-M
09-24-2014 11:53 PM
We have similar issue going on the below thread:
https://supportforums.cisco.com/discussion/11944481/glc-lx-2960-x-sfp-slot-wont-link-4503-sfp
Check if that helps
.
The Switch and IOS which you are running should support GLC-T SFp.
HTH
09-25-2014 05:40 AM
Thank you insharie
We try IOS Software EX3, EX4, EX5 and 15-2.2 but can't problem GLC-T hang
Which Port is GLC-T down , we try reload but don't can must unplug cable (220volt)
05-03-2018 09:41 PM
GLC-T is supported on the 2960S. Check the link below (Table 1-2)
http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/hardware/installation/guide_stack/HIGOVERV.html#wp1250224
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide