12-26-2017 02:15 AM - edited 03-08-2019 01:13 PM
Hi
We are trying to establish a Connection from our Cisco C6816 router to Azure-cloud( Express-route), to achieve this we need to use the QinQ VLAN configuration, I have done this on Nexus switch which is working fine, not able to get the exact config for Cisco 6816 router, can anyone share the config for Cisco 6816, this will be a great help.
" Nexus
interface GigabitEthernet<Interface_Number>.<Number>
encapsulation dot1Q <s-tag> seconddot1Q <c-tag>
ip address <IPv4_Address><Subnet_Mask>
12-26-2017 03:02 AM
Hello,
I remember this to be something like below:
switchport mode dot1q-tunnel
switchport vlan mapping enable
switchport vlan mapping 1501 701
12-26-2017 03:21 AM
hi
i added below config's still not working
interface Vlan1131
ip address 192.168.12.1 255.255.255.252
1)
interface TenGigabitEthernet1/2
switchport
switchport vlan mapping enable
switchport vlan mapping 1131 1132
switchport mode trunk
2)
interface TenGigabitEthernet1/2
switchport
switchport vlan mapping enable
switchport vlan mapping 1131 1132
switchport mode dot1q-tunnel
no cdp enable
both the case i'm not able to reach the destination IP
C6816-2513#ping 192.168.12.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.12.2, timeout is 2 seconds:
.....
12-26-2017 05:02 AM
Hello,
I think ' no lldp transmit' is required on the PE port. In your case, I don't know which port that is, try it on one or the other...
01-21-2018 12:42 PM - edited 01-21-2018 12:43 PM
Hi
Please find the attached connectivity FYR.
We are connecting to Microsoft Azure through one of the providers, where we need to use Q-in-Q (802.1ad), port te1/2 connected to Service provider.
As per our Provider "Cusertmerdevice should support 802.1ad (Q-in-Q) with inner/outer tags", we are using Cisco C6816-X-LE router to achieve this connection
The interface te1/2 connect to Service provider ( C-Tag 1141 S-Tag-1131) ( C-Tag-> Our end VLAN, S-TAG-> Service provider VLAN)
" https://docs.microsoft.com/en-us/azure/expressroute/expressroute-config-samples-routing "
C6816(config)#do sh run int te 1/2
interface TenGigabitEthernet1/2
switchport
switchport vlan mapping enable
switchport vlan mapping 1141 1131
switchport mode dot1q-tunnel
switchport access vlan 1131
no cdp enable
no lldp transmit
01-21-2018 02:34 PM - edited 01-21-2018 02:36 PM
Hello
My understanding is you apply QinQ on the SP switch facing your end hosts.
Sw1
int x/x
description facing rtr1
switchport mode dot1q-tunnel
l2protocol-tunnel CDP | VTP |STP
switchport access vlan 102 <--qinq tunnel vlan
Sw2
int x/x
description facing rtr2
switchport mode dot1q-tunnel
l2protocol-tunnel CDP | VTP |STP
switchport access vlan 102 <--qinq tunnel vlan
res
Paul
01-21-2018 05:25 PM
HI @paul driver
Thank you for the reply,
But in this case, where we are doing the VLAN mapping, as per the Service provider & Azure, we will have a VLAN 1141 on our & Azure end, VLAN 1131 is the Provider Q-in-Q tunnel VLAN,
Basically how it works is we need to send double-tagged frames with an outer tag of 1131 and an inner tag of1141 (used for Azure peerings)
When provider receive that they pass the traffic through their network, remove the outer tag of 1131 and replace it with the Azure "B VLAN (1141)" and send it to Azure
Azure remove the outer VLAN and then use the inner VLANs for individual peerings
If we send only single-tagged frames, or either of the tags is not correct, it won't work.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide