11-07-2013 12:59 AM - edited 03-07-2019 04:28 PM
Hi all,
on my 6509 I can do an show module see output below.
What is the OID to get the same result specially the "Online Diag Status"?
Thanks
Willem
rou0801#sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE SAL1513A9FV
4 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL09264M88
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL09285BUU
6 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL09285D84
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 c89c.1dc1.1374 to c89c.1dc1.1377 3.2 12.2(18r)S1 12.2(18)SXF1 Ok
4 0014.6af3.dcdc to 0014.6af3.dcf3 2.2 12.2(14r)S5 12.2(18)SXF1 Ok
5 0012.dae4.7df0 to 0012.dae4.7df3 4.4 8.1(3) 12.2(18)SXF1 Ok
6 0014.f215.b268 to 0014.f215.b297 2.2 12.2(14r)S5 12.2(18)SXF1 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
2 Centralized Forwarding Card WS-F6700-CFC SAL15119BAR 4.1 Ok
4 Centralized Forwarding Card WS-F6700-CFC SAL09285FFQ 2.0 Ok
5 Policy Feature Card 3 WS-F6K-PFC3B SAL09274YM9 2.1 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL09274U8K 2.3 Ok
6 Centralized Forwarding Card WS-F6700-CFC SAL09274T2C 2.0 Ok
Mod Online Diag Status
---- -------------------
2 Pass
4 Pass
5 Pass
6 Pass
rou0801#
11-07-2013 03:12 AM
Hi,
you can query the inventory-data by the objects of the ENTITY-MIB, e.g. entPhysicalDescr, entPhysicalSerialNum, etc.
For Information about the Diagnostic Status you can query the CISCO-ENTITY-DIAG-MIB, e.g. the object ceDiagTestPerfLastResult; this one will provide very similar information like a "show diagnostic result module
HTH
Rolf
11-07-2013 04:31 AM
Hi Rolf,
Thanks.
In ENTITY-MIB I don't find the Status.
My 6509 does not answer to CISCO-ENTITY-DIAG-MIB tree at all
The only partly usable result coes from:
1.3.6.1.4.1.9.3.6.11.1.9
Description:
The operational status of the card. cardOperStatus is up when a card is recognized by the device and is enabled for operation. cardOperStatus is down if the card is not recognized by the device, or if it is not enabled for operation. cardOperStatus is standby if the card is enabled and acting as a standby slave
Enumerations:
1 - not-specified
2 - up
3 - down
4 - standby Description:
I hoped that Online Diag Status shows a bit more information.
03-11-2024 12:31 AM - edited 03-11-2024 12:32 AM
Hi,
I'm currently have the same problem. I managed to get some output from my device, nevertheless I can't assign output to corresponding modules, e.g.:
[...]
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
4 Pass
6 Not Applicable
Is there a way to map these values to modules?
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.1000.1 = INTEGER: 3
[...]
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.1000.46 = INTEGER: 3
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.1000.47 = INTEGER: 4
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.2000.1 = INTEGER: 3
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.2000.2 = INTEGER: 3
[...]
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.2000.53 = INTEGER: 4
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.2000.54 = INTEGER: 3
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.3000.1 = INTEGER: 3
[...]
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.3000.46 = INTEGER: 3
SNMPv2-SMI::enterprises.9.9.350.1.6.1.1.1.3000.47 = INTEGER: 4
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide