Solved: show command for ASR 1004

johnlloyd_13 · ‎08-30-2012

hi all,

is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device.

i was only able to find 'test interface' but haven't run this yet (currently in production). thanks in advance!

#test interface g ?

<0-0> GigabitEthernet interface number

<0-1000> GMPLS interface number

<0-1> GigabitEthernet interface number

> show interfaces diagnostics optics ge-1/1/2

Physical interface: ge-1/1/2

Laser bias current : 16.576 mA

Laser output power : 1.6770 mW / 2.25 dBm

Module temperature : 44 degrees C / 111 degrees F

Module voltage : 3.1960 V

Receiver signal average optical power : 0.8565 mW / -0.67 dBm

Laser bias current high alarm : Off

Laser bias current low alarm : Off

Laser bias current high warning : Off

Laser bias current low warning : Off

Laser output power high alarm : Off

Laser output power low alarm : Off

Laser output power high warning : Off

Laser output power low warning : Off

Module temperature high alarm : Off

Module temperature low alarm : Off

Module temperature high warning : Off

Module temperature low warning : Off

Module voltage high alarm : Off

Module voltage low alarm : Off

Module voltage high warning : Off

Module voltage low warning : Off

Laser rx power high alarm : On

Laser rx power low alarm : Off

Laser rx power high warning : On

Laser rx power low warning : Off

Laser bias current high alarm threshold : 100.000 mA

Laser bias current low alarm threshold : 6.000 mA

Laser bias current high warning threshold : 95.000 mA

Laser bias current low warning threshold : 6.498 mA

Laser output power high alarm threshold : 5.0120 mW / 7.00 dBm

Laser output power low alarm threshold : 0.6300 mW / -2.01 dBm

Laser output power high warning threshold : 3.9810 mW / 6.00 dBm

Laser output power low warning threshold : 0.7940 mW / -1.00 dBm

Module temperature high alarm threshold : 85 degrees C / 185 degrees F

Module temperature low alarm threshold : -15 degrees C / 5 degrees F

Module temperature high warning threshold : 80 degrees C / 176 degrees F

Module temperature low warning threshold : -10 degrees C / 14 degrees F

Module voltage high alarm threshold : 3.600 V

Module voltage low alarm threshold : 3.000 V

Module voltage high warning threshold : 3.499 V

Module voltage low warning threshold : 3.099 V

Laser rx power high alarm threshold : 0.7943 mW / -1.00 dBm

Laser rx power low alarm threshold : 0.0025 mW / -26.02 dBm

Laser rx power high warning threshold : 0.6309 mW / -2.00 dBm

Laser rx power low warning threshold : 0.0031 mW / -25.09 dBm

Ivan Shirshin · ‎08-30-2012

Hi John,

There is a command like "show hw-module subslot ... transceiver ... idprom detail" to see port parameters and "show hw-module subslot ... transceiver ... status" to see current status:

Router# show hw-module subslot 4/0 transceiver 2 status 
The Transceiver in slot 4 subslot 0 port 2 is enabled.
  Module temperature                = +41.617 C
  Transceiver Tx supply voltage     = 3292.0 uVolts
  Transceiver Tx bias current       = 4840 uAmps
  Transceiver Tx power              = 349.2 uWatts
  Transceiver Rx optical power      = 0.5 uWatts

Router# show hw-module subslot 4/0 transceiver 5 idprom detail
 
IDPROM for transceiver GigabitEthernet4/0/6:
  Description                               = SFP optics (type 3)
  Transceiver Type:                         = GE SX (19)
  Product Indentifier (PID)                 = FTRJ8519P1BNL-C3
  Vendor Revision                           = A1
  Serial Number (SN)                        = FNS0821K2J5     
  Vendor Name                               = CISCO-FINISAR   
  Vendor OUI (IEEE company ID)              = 00.90.65 (36965)
  CLEI code                                 = CNUIAAMAAA
  Cisco part number                         = 10-1954-01
  Device State                              = Enabled.
  Date code (yy/mm/dd)                      = 04/05/19
  Connector type                            = LC.
  Encoding                                  = 8B10B
                                              NRZ
  Nominal bitrate                           = 2xFC (2100 Mbits/s)
  Minimum bit rate as % of nominal bit rate = not specified
  Maximum bit rate as % of nominal bit rate = not specified
  Link reach for 9u fiber (km)              = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 9u fiber (m)               = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 50u fiber (m)              = 2xFC-MM(300/150m) (30)
  Link reach for 62.5u fiber (m)            = 2xFC-MM(300/150m) (15)
  Nominal laser wavelength                  = 850 nm.
  DWDM wavelength fraction                  = 850.0  nm.
  Supported options                         = Tx disable
                                              Tx fault signal
                                              Loss of signal (standard implementation)
  Supported enhanced options                = Alarms for monitored parameters
  Diagnostic monitoring                     = Digital diagnostics supported
                                              Diagnostics are externally calibrated
                                              Rx power measured is "Averagepower"
  Transceiver temperature operating range   = -5 C to 85 C (extended)
  Minimum operating temperature             = -20 C
  Maximum operating temperature             = 90 C
  High temperature alarm threshold          = +109.000 C
  High temperature warning threshold        = +103.000 C
  Low temperature warning threshold         =  -13.000 C
  Low temperature  alarm threshold          =  -29.000 C
  High voltage alarm threshold              = 3.9000 Volts
  High voltage warning threshold            = 3.7000 Volts
  Low voltage warning threshold             = 2.9000 Volts
  Low voltage alarm threshold               = 2.7000 Volts
  High laser bias current alarm threshold   = 15.000 mAmps
  High laser bias current warning threshold = 12.000 mAmps
  Low laser bias current warning threshold  = 2.000 mAmps
  Low laser bias current alarm threshold    = 1.000 mAmps
  High transmit power alarm threshold       = 0.7424 mWatts
  High transmit power warning threshold     = 0.7424 mWatts
  Low transmit power warning threshold      = 0.959 mWatts
  Low transmit power alarm threshold        = 0.619 mWatts
  High receive power alarm threshold        = 5.9324 mWatts
  High receive power warning threshold      = 3.7416 mWatts
  Low receive power warning threshold       = 0.751 mWatts
  Low receive power alarm threshold         = 0.478 mWatts
  External Calibration constant: Rx power4  = 0.000
  External Calibration constant: Rx power3  = 0.000
  External Calibration constant: Rx power2  = 0.000
  External Calibration constant: Rx power1  = 0.212
  External Calibration constant: Rx power0  = -1.4294966868
  External Calibration: bias current slope  = 1.000
  External Calibration: bias current offset = 0

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

View solution in original post

Ivan Shirshin · ‎08-30-2012

Hi John,

There is a command like "show hw-module subslot ... transceiver ... idprom detail" to see port parameters and "show hw-module subslot ... transceiver ... status" to see current status:

Router# show hw-module subslot 4/0 transceiver 2 status 
The Transceiver in slot 4 subslot 0 port 2 is enabled.
  Module temperature                = +41.617 C
  Transceiver Tx supply voltage     = 3292.0 uVolts
  Transceiver Tx bias current       = 4840 uAmps
  Transceiver Tx power              = 349.2 uWatts
  Transceiver Rx optical power      = 0.5 uWatts

Router# show hw-module subslot 4/0 transceiver 5 idprom detail
 
IDPROM for transceiver GigabitEthernet4/0/6:
  Description                               = SFP optics (type 3)
  Transceiver Type:                         = GE SX (19)
  Product Indentifier (PID)                 = FTRJ8519P1BNL-C3
  Vendor Revision                           = A1
  Serial Number (SN)                        = FNS0821K2J5     
  Vendor Name                               = CISCO-FINISAR   
  Vendor OUI (IEEE company ID)              = 00.90.65 (36965)
  CLEI code                                 = CNUIAAMAAA
  Cisco part number                         = 10-1954-01
  Device State                              = Enabled.
  Date code (yy/mm/dd)                      = 04/05/19
  Connector type                            = LC.
  Encoding                                  = 8B10B
                                              NRZ
  Nominal bitrate                           = 2xFC (2100 Mbits/s)
  Minimum bit rate as % of nominal bit rate = not specified
  Maximum bit rate as % of nominal bit rate = not specified
  Link reach for 9u fiber (km)              = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 9u fiber (m)               = SX(550/270m) (0)
                                              1xFC-MM(500/300m) (0)
                                              2xFC-MM(300/150m) (0)
                                              ESCON-MM(2km) (0)
  Link reach for 50u fiber (m)              = 2xFC-MM(300/150m) (30)
  Link reach for 62.5u fiber (m)            = 2xFC-MM(300/150m) (15)
  Nominal laser wavelength                  = 850 nm.
  DWDM wavelength fraction                  = 850.0  nm.
  Supported options                         = Tx disable
                                              Tx fault signal
                                              Loss of signal (standard implementation)
  Supported enhanced options                = Alarms for monitored parameters
  Diagnostic monitoring                     = Digital diagnostics supported
                                              Diagnostics are externally calibrated
                                              Rx power measured is "Averagepower"
  Transceiver temperature operating range   = -5 C to 85 C (extended)
  Minimum operating temperature             = -20 C
  Maximum operating temperature             = 90 C
  High temperature alarm threshold          = +109.000 C
  High temperature warning threshold        = +103.000 C
  Low temperature warning threshold         =  -13.000 C
  Low temperature  alarm threshold          =  -29.000 C
  High voltage alarm threshold              = 3.9000 Volts
  High voltage warning threshold            = 3.7000 Volts
  Low voltage warning threshold             = 2.9000 Volts
  Low voltage alarm threshold               = 2.7000 Volts
  High laser bias current alarm threshold   = 15.000 mAmps
  High laser bias current warning threshold = 12.000 mAmps
  Low laser bias current warning threshold  = 2.000 mAmps
  Low laser bias current alarm threshold    = 1.000 mAmps
  High transmit power alarm threshold       = 0.7424 mWatts
  High transmit power warning threshold     = 0.7424 mWatts
  Low transmit power warning threshold      = 0.959 mWatts
  Low transmit power alarm threshold        = 0.619 mWatts
  High receive power alarm threshold        = 5.9324 mWatts
  High receive power warning threshold      = 3.7416 mWatts
  Low receive power warning threshold       = 0.751 mWatts
  Low receive power alarm threshold         = 0.478 mWatts
  External Calibration constant: Rx power4  = 0.000
  External Calibration constant: Rx power3  = 0.000
  External Calibration constant: Rx power2  = 0.000
  External Calibration constant: Rx power1  = 0.212
  External Calibration constant: Rx power0  = -1.4294966868
  External Calibration: bias current slope  = 1.000
  External Calibration: bias current offset = 0

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

johnlloyd_13 · ‎08-30-2012

ivan,

you're awesome! thanks!

i tried googling for CLI commands for ASR but only gave me specs. would highly appreciate if you could give me a link?

>sh hw-module subslot 0/0 transceiver 4 status

The Transceiver in slot 0 subslot 0 port 4 is enabled.

Module temperature = +32.437 C

Transceiver Tx supply voltage = 3271.0 mVolts

Transceiver Tx bias current = 28796 uAmps

Transceiver Tx power = 2.9 dBm

Transceiver Rx optical power = -26.6 dBm

>sh hw-module subslot 0/0 transceiver 4 idprom detail

IDPROM for transceiver GigabitEthernet0/0/4:

Description = SFP optics (type 3)

Transceiver Type: = GE ZX (23)

Ivan Shirshin · ‎08-30-2012

Welcome, John :-)

Here are the links:

http://www.cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/configuration/ASR1000/ASRcfget.html#wp1221123

http://www.cisco.com/en/US/products/hw/routers/ps368/module_installation_and_configuration_guides_chapter09186a0080440152.html#wp1429536

http://www.cisco.com/en/US/docs/ios-xml/ios/interface/command/ir-s4.html#GUID-B2639B26-EA81-4E02-BE8A-7CE8FB9D17BF

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

johnlloyd_13 · ‎08-30-2012

thanks a lot!

Ivan Shirshin · ‎08-30-2012

Welcome and thanks for ratings!

Kind Regards,
Ivan

CSCO11868810 · ‎07-01-2016

Hello guys,

there is a way to enable log on ASR 1000 for transceiver problem about TX/RX power?

i can see the values of TX RX by the command : sh hw-module subslot 0/0 transceiver xxx....., but if i have a problem the device doesn't reply any logs....

thks,

Ale