Stack issue-help Required

muhsi_2015 · ‎02-24-2016

Hi,

All the stacck members have the same ios . But out of five two members showing .Does it mean there is an issue ?

I have rebooted couple of times to see whether it bring correct version or not ? .

But nothing happened .

( I had to reboot whole stack since there was no console or remote access , before rebooting switch 3 and 5 were showing correct hardware version )

Switch Ports Model              SW Version        SW Image              Mode
------ ----- -----              ----------        ----------            ----
*    1 56    WS-C3850-48P       03.03.05SE        cat3k_caa-universalk9 INSTALL
     2 56    WS-C3850-48P       03.03.05SE        cat3k_caa-universalk9 INSTALL
     3 56    WS-C3850-48P       03.03.05SE        cat3k_caa-universalk9 INSTALL
     4 56    WS-C3850-48P       03.03.05SE        cat3k_caa-universalk9 INSTALL
     5 56    WS-C3850-48P       03.03.05SE        cat3k_caa-universalk9 INSTALL

sh switch
Switch/Stack Mac Address : 8890.80 - Local Mac Address
Mac persistency wait time: Indefinite
                                             H/W   Current
Switch#   Role    Mac Address     Priority Version State
------------------------------------------------------------
*1       Active   8890..x.x.x.x     15     V04     Ready
2       Standby 8890.8d18.x.x.x.x    14     V04     Ready
3       Member   8890.8d18.x.x.x.x    13     0       Ready
4       Member   40a6.x.x.x.x.x.x.x.x   12     V04     Ready
5       Member   8890.8d07.x.x.x.x     11     0       Ready

sh switch stack-ring speed

Stack Ring Speed        : 480G
Stack Ring Configuration: Full
Stack Ring Protocol     : StackWise

show switch neighbors
Switch #    Port 1       Port 2
--------    ------       ------
      1         2             4
      2         3             1
      3         5             2
      4         1             5
      5         4             3

Please help

Thanks

Leo Laohoo · ‎02-25-2016

There is nothing to be worried about the differences with "HW version". The main thing to look out for is the IOS-XE software version.

muhsi_2015 · ‎02-25-2016

Hi ,

Thank you for the reply . My concern was before rebooting all hardware version were same like below

Switch#   Role    Mac Address     Priority Version State
------------------------------------------------------------
*1       Active   8890..x.x.x.x     15     V04     Ready
2       Standby 8890.8d18.x.x.x.x    14     V04     Ready
3       Member   8890.8d18.x.x.x.x    13     V04      Ready
4       Member   40a6.x.x.x.x.x.x.x.x   12     V04     Ready
5       Member   8890.8d07.x.x.x.x     11     V04      Ready

and after rebooting all stacks it became like below

Switch#   Role    Mac Address     Priority Version State
------------------------------------------------------------
*1       Active   8890..x.x.x.x     15     V04     Ready
2       Standby 8890.8d18.x.x.x.x    14     V04     Ready
3       Member   8890.8d18.x.x.x.x    13     0       Ready
4       Member   40a6.x.x.x.x.x.x.x.x   12     V04     Ready
5       Member   8890.8d07.x.x.x.x     11     0       Ready

I don't have any clue why member 3 and 5's hardware version became '0'

Thank you

Leo Laohoo · ‎02-25-2016

Could be a bug.

atisingh · ‎05-26-2021

.