Switch stacking
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 01:27 AM - edited 03-08-2019 12:27 PM
I have two switches 3850 , Please check the configuration ,
Why the LID stacking is not working , The configuration is attached file is correct or NOT
- Labels:
-
Other Switching
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 01:45 AM
Hi,
@eng_adel273 wrote:
I have two switches 3850 , Please check the configuration ,
Why the LID stacking is not working , The configuration is attached file is correct or NOT
In your configuration, the LID (Local ID also known as Port ID) is named correctly. I saw interface GigabitEthernet 1/0/1 as well as interface GigabitEthernet 2/0/1. Did I miss anything?
HTH,
Meheretab
Meheretab
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 02:12 AM
sorry , I means , LED light for stacking in front of the switch
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 02:43 AM
#show switch detail
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 02:54 AM
Switch# Role Mac Address Priority Version St
------------------------------------------------------
*1 Active 0057.d2ae.9600 5 V03 Re
2 Standby 00da.551e.dc80 1 V03 Re
Stack Port Status Neighbors
Switch# Port 1 Port 2 Port 1 Port 2
------------------------------------------------------
1 OK OK 2 2
2 OK OK 1 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 03:07 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 03:09 AM
Mark Answered if this resolves & rate if helpful.
Thanks
Arun
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 03:35 AM
Press the Mode button on a stack member until the Stack mode LED is on. The last two port LEDs on the switch should be green. Depending on the switch model, the last two ports are either 10/100/1000 ports or small form-factor pluggable (SFP) module. If one or both of the last two port LEDs are not green, the stack is not operating at full bandwidth.
this should work or if you are running 3.7.3 there might be bug also not sure this bug in other version
https://cdetsng.cisco.com/webui/#view=CSCuy43591
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 04:01 AM
Thank you for your support
Is the configuration contains redundancy or Not ?
What happened if I turned off one Switch for example Active switch ?
How I apply redundany between two switches
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 07:20 AM
if you turn off active switch . standby wil become active and works fine ..
rate if helpful.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-22-2017 07:42 AM - edited 10-22-2017 03:43 PM
Is the configuration contains redundancy or Not ?
What happened if I turned off one Switch for example Active switch ?
How I apply redundany between two switches
Meheretab
