04-28-2011 01:27 PM - edited 03-06-2019 04:50 PM
trying to configure vPC on nexus 5K running into issues.
PeerLink
Nexus5KA-----------------Nexus 5KB
| |
| |
Nexus2KA Nexus2KB
| |
Cisco Load Balancer
Need to connect my cisco load balancer interfaceGi1/1 -- interface Ethernet138/1/2 on nexus 2KA
InterfaceGi1/2---interface Ethernet138/1/2 on nexus 2KB
need to configure vPC for the making load Balancer highly redundant
Here is the config i had on my 5Ks,able to create a peer link and flex fabric ,but running into issues with vPC
looks like configured everything but vpc is not working.
Nexus 5K A:
vpc domain 2
role priority 100
system-priority 100
peer-keepalive destination 10.18.168.72 source 10.18.168.71
interface port-channel101
description PPPPPPPPPP-Eth 1/1, Eth 1/2-PPPPPPPPPPPPP
switchport mode trunk
vpc peer-link
switchport trunk allowed vlan 1,10,200
spanning-tree port type network
speed 10000
interface port-channel110
switchport mode trunk
vpc 110
switchport trunk allowed vlan 200
interface Ethernet1/1
description PortChannelPortChannel 5kb 1/1,1/2 PortChannelPortChannel
switchport mode trunk
switchport trunk allowed vlan 1,10,200
channel-group 101 mode active
interface Ethernet1/2
description PortChannelPortChannel 5kb 1/1,1/2 PortChannelPortChannel
switchport mode trunk
switchport trunk allowed vlan 1,10,200
channel-group 101 mode active
fex 138
pinning max-links 1
description FEX0138
interface Ethernet1/38
fex associate 138
switchport mode fex-fabric
Nexus5KB:
vpc domain 2
role priority 200
system-priority 100
peer-keepalive destination 10.18.168.71 source 10.18.168.72
interface port-channel101
description PPPPPPPPPP-Eth 1/1, Eth 1/2-PPPPPPPPPPPPP
switchport mode trunk
vpc peer-link
switchport trunk allowed vlan 1,10,200
spanning-tree port type network
speed 10000
interface Ethernet1/1
description PortChannelPortChannel 5ka 1/1,1/2 PortChannelPortChannel
switchport mode trunk
switchport trunk allowed vlan 1,10,200
channel-group 101 mode active
interface Ethernet1/2
description PortChannelPortChannel 5ka 1/1,1/2 PortChannelPortChannel
switchport mode trunk
switchport trunk allowed vlan 1,10,200
channel-group 101 mode active
fex 138
pinning max-links 1
description FEX0138
interface Ethernet1/38
fex associate 138
switchport mode fex-fabric
ACE :
interface port-channel110
switchport mode trunk
switchport trunk allowed vlan 200
interface gigabitEthernet 1/1
description conn to nex2kA
switchport trunk allowed vlan 200
channel-group 110 mode active
no shutdown
interface gigabitEthernet 1/2
switchport trunk allowed vlan 200
description conn to nex2kB
channel-group 110 mode active
no shutdown
04-29-2011 01:19 AM
Hi,
Could you please be a bit more specific about what issues you're observing?
Please paste the output of the following commands.
show port-channel summary
show vpc
show vpc consistency-parameters global
Best regards,
Andras
05-03-2011 07:57 AM
Here is the output
sw5ka# sh vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 2
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status: success
vPC role : primary
Number of vPCs configured : 2
Peer Gateway : Disabled
Dual-active excluded VLANs : -
vPC Peer-link status
---------------------------------------------------------------------
id Port Status Active vlans
-- ---- ------ --------------------------------------------------
1 Po101 up 1,101-102,817,997
vPC status
----------------------------------------------------------------------------
id Port Status Consistency Reason Active vlans
------ ----------- ------ ----------- -------------------------- -----------
110 Po110 down* success success -
139 Po139 up success success 1,101-102,8
17,997
5ka# show port-channel summary
Flags: D - Down P - Up in port-channel (members)
I - Individual H - Hot-standby (LACP only)
s - Suspended r - Module-removed
S - Switched R - Routed
U - Up (port-channel)
--------------------------------------------------------------------------------
Group Port- Type Protocol Member Ports
Channel
--------------------------------------------------------------------------------
101 Po101(SU) Eth LACP Eth1/1(P) Eth1/2(P)
110 Po110(SD) Eth LACP Eth138/1/25(I)
139 Po139(SU) Eth LACP Eth1/39(P) Eth1/40(P)
5ka# sh vpc consistency-parameters global
Legend:
Type 1 : vPC will be suspended in case of mismatch
Name Type Local Value Peer Value
------------- ---- ---------------------- -----------------------
QoS 1 ([], [3], [], [], [], ([], [3], [], [], [],
[]) [])
Network QoS (MTU) 1 (1538, 2240, 0, 0, 0, (1538, 2240, 0, 0, 0,
0) 0)
Network Qos (Pause) 1 (F, T, F, F, F, F) (F, T, F, F, F, F)
Input Queuing (Bandwidth) 1 (50, 50, 0, 0, 0, 0) (50, 50, 0, 0, 0, 0)
Input Queuing (Absolute 1 (F, F, F, F, F, F) (F, F, F, F, F, F)
Priority)
Output Queuing (Bandwidth) 1 (50, 50, 0, 0, 0, 0) (50, 50, 0, 0, 0, 0)
Output Queuing (Absolute 1 (F, F, F, F, F, F) (F, F, F, F, F, F)
Priority)
STP Mode 1 Rapid-PVST Rapid-PVST
STP Disabled 1 None None
STP MST Region Name 1 "" ""
STP MST Region Revision 1 0 0
STP MST Region Instance to 1
VLAN Mapping
STP Loopguard 1 Disabled Disabled
STP Bridge Assurance 1 Enabled Enabled
STP Port Type, Edge 1 Normal, Disabled, Normal, Disabled,
BPDUFilter, Edge BPDUGuard Disabled Disabled
STP MST Simulate PVST 1 Enabled Enabled
Allowed VLANs - 1,101-102,817,997 1,101-102,817,997
Local suspended VLANs - - -
s0labsw5ka#
05-10-2011 11:37 AM
Hi
Do you have vlan 200 allowed through your peer-links (port101)? I do see it on your initial configs but then again I did not see other vlans allowed like you have here so did you change you initial configuration or is that just a partial configuration to show that you do have those vlans going through?
interface port-channel101
description PPPPPPPPPP-Eth 1/1, Eth 1/2-PPPPPPPPPPPPP
switchport mode trunk
vpc peer-link
switchport trunk allowed vlan 1,10,200
spanning-tree port type network
speed 10000
----------------------------------------------------------------------
1 Po101 up 1,101-102,817,997
Second question is are you using a ACE4710 appliance? If so I thought LACP and PAGP was not supported on them. (see ACE 4710 Design Guide.pdf)
The way we have our LB connected to our Nexus in a vPC is that we have our ACE 4710 configured in port-channel mode on not using LACP and on our Nexus we have it also on port-channel mode on. It works fine.
interface Eth138/1/25
channel-group 110 mode on
hope this helps....
-E
05-10-2011 11:43 AM
--
05-10-2011 09:20 PM
Yes ,Vlan200 is trunked between the peers.
05-10-2011 09:25 PM
Emil Versoza
Configured port channel on ACE1 .
interface gigabitEthernet 1/1
description conn to nex2kA
channel-group 110
no shutdown
interface gigabitEthernet 1/2
description conn to nex2kB
channel-group 110
no shutdown
interface port-channel 110
switchport trunk allowed vlan 817
no shutdown
I am struck with another issue i.e ,How to setup the standby ACE for vPC ,as initially ,I though of creating another portchannel on my nexus for ACE2,but later on realised that it will have the exact copy of config as that of active.
If the active fails ,how will the standby takeover on the nexus5K with vPC on please help me.
05-13-2011 02:23 PM
Hi Kalugotla1
you are right go ahead on the nexus create another vPC for the standby ACE. The ACEs will communicate thru the FT Vlan if active is unresponsive a switchover will occur.
hope this helps.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide