HiPlease could someone explain the below output from the command issued.The mutlicast source is as below 10.120.50.69.Two things in question. 1.) Why is the *,232.0.10.38 forwarding? 2.) What is it forwarding?1# sh ip mroute 232.0.10.38IP Mul...
Hello Everyone,I have a 3560 switch 48-PS, and i need plug two IP phones 7911. But do not get the power in the ports, and the phones do not start.Show power inline command:Available:370.0(w) Used:85.9(w) Remaining:284.1(w)Interface Admin Oper ...
Hi experts,I don't know if i've posted in the right thread. But anyway, I would like to know a good Cisco Fibre switch not too expensive, which supports the following:VLAN Inter-Vlan RoutingSFP Port between 8-16 portsSpeed: between 1 - 10 GigabitThan...
Hi,I'm new to QOS world and need a solution and understanding for the following scenario:PC1 ------ SW1 -------- SW2 ------- PC2All the ports are in the same vlan, the switches are both 3560 and their is no SVI created on these switches. There is no ...
Hi, I have a question with regards to loopgaurd. If you have a block of 6 access switches daisy chained together and you uplink switches 1 and 6 back to the distribution layer. This means spanning tree blocks a port in the centre of the block so the ...
Hola,Necesito formar un Virtual Switch System entre dos Switches 6506. El procedimiento lo tengo mas o menos claro, mi duda es: En ambos switches hay actualmente puertos configurados y conectados a otros equipos. Al convertir ambos switches para form...
Hi All,We are in the process of upgrading IOS for cisco 6509. Can i know the stable version of IOS which supports IP v6. Below are the switch model & SUP engine details1. Cisco 6509 --- WS-F6K-MSFC22. Cisco 6509-E --- WS-SUP720 Thanks in advance.Rega...
All,I was wondering if somebody would advise me if the NX-OS on the Cisco NEXUS 7000 supports reflexive ACL's. I dont currently have the device so Im unable to take a look. Thanks all,Winning44
My Cisco 6500 has the following card:WS-X6324-100FX-SM. Has anybody used a FSD9-MTMT-03 instead of CAB-MTRJ-SC-SM-3M? The generic cable is definitely must be cheaper.-Mn
I'm a noob when it comes to QoS and I have been doing a good bit of reading and testing lately with QoS. Right now in our environment all of our PoE switches are 2960S switches, we also have all Cisco VoIP phones (7942, 7945s). So the 2960s connect v...
I am running MST on my network with 1 instance right now but will soon be 2. If I issue the show spanning-tree command here is what I see:MIB-SW-CORE-01#show spanning-treeMST0 Spanning tree enabled protocol mstp Root ID Priority 32768 ...
Hi guys I have a cisco 3560 that will be connected to a Microwave device via a 10 Mbps link(I mean my FE will be configured to 10Mbps speed) .The bandwidth on the microwave is 512kbps and the microwave device does not support flow control.So i need t...
I have a question how can a connection to a specific ip address mac-address
Hi,Is L2/L3 rate limiting or policing supported on EHWIC-4ESG card on 1941 router?TIAHitesh
I'm attempting to bridge two locations.One is on the third floor of the building with a number of vlans.The other is in the basement (a C4948).I want to trunk the vlans from the third floor down to the basement.Once they are trunked down there, I wan...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
