Width of 'show interfaces summary'

Andras Dosztal · ‎09-25-2012

Hi,

Is there a way to set the columns' width of the sh int sum output? It's too narrow for the 10GbE interfaces:

switch#sh int sum | i ^\* Te|^\* Gi

* TenGigabitEthernet 0 4 0 0 467347000 60834 164015000 23424 911

* TenGigabitEthernet 0 686 0 0 218561000 21090 80883000 11138 0

* TenGigabitEthernet 0 4 0 0 2330000 605 17087000 1907 0

* TenGigabitEthernet 0 4 0 0 2042000 292 15836000 1555 0

* TenGigabitEthernet 0 61 0 0 112811000 15247 251409000 39872 188

* TenGigabitEthernet 0 6 0 0 86756000 22203 251420000 34686 0

* TenGigabitEthernet 0 2 0 0 20439000 1892 16579000 2350 0

* TenGigabitEthernet 0 32 0 0 23993000 3934 4642000 2816 0

* TenGigabitEthernet 0 5 0 0 249621000 31705 539032000 49803 0

* TenGigabitEthernet 0 5 0 0 69321000 9316 38846000 8749 0

* TenGigabitEthernet 0 12 0 0 73150000 9309 87643000 10468 0

* TenGigabitEthernet 0 5 0 0 121263000 11824 65664000 9111 0

* GigabitEthernet7/1 0 0 0 0 244000 103 4826000 505 0

* GigabitEthernet7/2 0 504 0 0 146000 47 10402000 952 0

* GigabitEthernet7/3 0 0 0 0 142000 61 5019000 549 0

* GigabitEthernet7/4 0 0 0 0 32000 22 10399000 898 0

* GigabitEthernet7/5 0 0 0 0 0 0 1000 1 0

* GigabitEthernet7/6 0 11 0 0 7000 4 21000 36 0

* GigabitEthernet7/7 0 12 0 0 0 0 3000 5 0

* GigabitEthernet7/8 0 6 0 0 0 0 15000 3 0

* GigabitEthernet7/9 0 8 0 0 84000 6 3000 2 0

* GigabitEthernet7/1 0 0 0 0 0 0 0 0 0

The terminal width <xx> command didn't help.

Harrie Hendriks · ‎09-25-2012

I was testing the command on the CAT6500 switches and there is a correct answere.

* TenGigabitEthernet2/1 0 0 0 0 37033000 12953 1195000 540 0

* TenGigabitEthernet2/2 0 0 0 0 77390000 13773 0 0 0

* GigabitEthernet3/1 0 0 0 0 7000 2 5000 10 0

* GigabitEthernet3/11 0 0 0 0 4000 3 4000 4 0

Maybe a problem in the IOS?

With Regards, Harrie