03-28-2018 07:11 AM - edited 03-08-2019 02:26 PM
I will try to connect two WS-C3650-24TS switches with GLC-GE-100FX SFP modules. Link is up.
Packet is outcome from one interface, but do not come to another interface. Test with ping. The settings on both switches are the same.
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 28 WS-C3650-24TS 16.6.2 CAT3K_CAA-UNIVERSALK9 INSTALL
C3650Primary#sh int gigabitEthernet 1/1/1 transceiver ITU Channel not available (Wavelength not available), Transceiver is externally calibrated. If device is externally calibrated, only calibrated values are printed. ++ : high alarm, + : high warning, - : low warning, -- : low alarm. NA or N/A: not applicable, Tx: transmit, Rx: receive. mA: milliamperes, dBm: decibels (milliwatts). Optical Optical Temperature Voltage Current Tx Power Rx Power Port (Celsius) (Volts) (mA) (dBm) (dBm) --------- ----------- ------- -------- -------- -------- Gi1/1/1 37.9 3.26 28.0 -16.7 -16.7 C3650Primary#sh int gigabitEthernet 1/1/1 capa C3650Primary#sh int gigabitEthernet 1/1/1 capabilities GigabitEthernet1/1/1 Model: WS-C3650-24TS Type: 100BaseFX SFP Speed: 100 Duplex: full,half Trunk encap. type: 802.1Q Trunk mode: on,off,desirable,nonegotiate Channel: yes Broadcast suppression: percentage(0-100) Flowcontrol: rx-(off,on,desired),tx-(none) Fast Start: yes QoS scheduling: rx-(not configurable on per port basis), tx-(2p6q3t) CoS rewrite: yes ToS rewrite: yes UDLD: yes Inline power: no SPAN: source/destination PortSecure: yes Dot1x: yes C3650Primary#sh int gigabitEthernet 1/1/1 GigabitEthernet1/1/1 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 7069.5a65.3f99 (bia 7069.5a65.3f99) MTU 1500 bytes, BW 10000 Kbit/sec, DLY 1000 usec, reliability 253/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Mb/s, link type is force-up, media type is 100BaseFX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters 00:48:46 Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 9664 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 44 input errors, 44 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 2109 packets output, 154776 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out C3650Primary#sh run int gigabitEthernet 1/1/1 Building configuration... Current configuration : 104 bytes ! interface GigabitEthernet1/1/1 switchport access vlan 1121 switchport mode access duplex full end
C3650Secondary#sh int gi1/1/1 transceiver ITU Channel not available (Wavelength not available), Transceiver is externally calibrated. If device is externally calibrated, only calibrated values are printed. ++ : high alarm, + : high warning, - : low warning, -- : low alarm. NA or N/A: not applicable, Tx: transmit, Rx: receive. mA: milliamperes, dBm: decibels (milliwatts). Optical Optical Temperature Voltage Current Tx Power Rx Power Port (Celsius) (Volts) (mA) (dBm) (dBm) --------- ----------- ------- -------- -------- -------- Gi1/1/1 39.6 3.26 32.7 -16.6 -15.7 C3650Secondary#sh int gi1/1/1 capa C3650Secondary#sh int gi1/1/1 capabilities GigabitEthernet1/1/1 Model: WS-C3650-24TS Type: 100BaseFX SFP Speed: 100 Duplex: full,half Trunk encap. type: 802.1Q Trunk mode: on,off,desirable,nonegotiate Channel: yes Broadcast suppression: percentage(0-100) Flowcontrol: rx-(off,on,desired),tx-(none) Fast Start: yes QoS scheduling: rx-(not configurable on per port basis), tx-(2p6q3t) CoS rewrite: yes ToS rewrite: yes UDLD: yes Inline power: no SPAN: source/destination PortSecure: yes Dot1x: yes C3650Secondary#sh int gi1/1/1 GigabitEthernet1/1/1 is up, line protocol is up (connected) Hardware is Gigabit Ethernet, address is 7069.5a99.3d19 (bia 7069.5a99.3d19) MTU 1500 bytes, BW 10000 Kbit/sec, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not set Full-duplex, 10Mb/s, link type is force-up, media type is 100BaseFX SFP input flow-control is off, output flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:00:01, output hang never Last clearing of "show interface" counters 00:50:08 Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 10143 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 45 input errors, 45 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 1578 packets output, 121114 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out C3650Secondary#sh run int gi1/1/1 Building configuration... Current configuration : 104 bytes ! interface GigabitEthernet1/1/1 switchport access vlan 2121 switchport mode access duplex full end
Solved! Go to Solution.
03-29-2018 11:07 PM - edited 03-29-2018 11:09 PM
Downgrade to 03.07.05E (cat3k_caa-universalk9.SPA.03.07.05.E.152-3.E5.bin). Traffic has gone through a 100BaseFx connection. The LED indicator on the port was working correctly. Command 'show interface' show the correct speed of 100Mb/s.
03-28-2018 08:17 AM
Can try removing
duplex full
from each switch and test again?
HTH
03-28-2018 10:29 AM
I already checked half-duplex, it was by default. Output collision count increased. No input packet.
03-28-2018 12:27 PM
03-28-2018 11:14 PM
Which version should I update? 16.6.3 (cat3k_caa-universalk9.16.06.03.SPA.bin)?
03-28-2018 11:29 PM
03-29-2018 03:46 AM
I updated both switches to version 16.6.3 and performed the checks. I did not notice any changes. Problem still exists.
03-29-2018 04:26 AM
Raise a TAC case. I believe you're hitting CSCvb69066.
03-29-2018 06:19 AM
Which one is correct?
interface GigabitEthernet1/1/1 switchport access vlan 2121
interface GigabitEthernet1/1/1 switchport access vlan 1121
03-29-2018 11:07 PM - edited 03-29-2018 11:09 PM
Downgrade to 03.07.05E (cat3k_caa-universalk9.SPA.03.07.05.E.152-3.E5.bin). Traffic has gone through a 100BaseFx connection. The LED indicator on the port was working correctly. Command 'show interface' show the correct speed of 100Mb/s.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide