Solved: Re: ws-c4948 10G I could use some help please. - Page 2

TroyGillian12627 · ‎01-29-2020

So I'm brand new to Cisco awesome equipment though. I bought a switch and when I first booted it up it was stuck in a boot-loop. So I researched and read and through trial and error I got it unstuck and the correct image in place. So I am configuring the switch have not done a tftp server yet and follow a wrong procedure and assign the wrong ip address to the switch I was supposed to be doing a loop-back. So I figured I would just start over good practice right. I'm trying to self teach myself Cisco here that should tell you I'm not the brightest crayon in the box. So I do a clear config all and it works great so great that even though I had supposedly done a running config save I now have no boot image no slot0 image and no boot system flash bootflash image. I did however make me a tftp server with tftp64 but cant for the life of me get the command right for Rommon to drop me an image. Hell at one point I could see on a reset it said boot booted from 0x010 cat4500-entservicesk9-mz.150-2.SG10.bin it was right there just not in the right position I have been driving myself crazy here could someone please throw me in the right direction?

Rom Monitor Program Version 12.2(31r)SGA4
Supervisor: WS-C4948 Chassis: WS-C4948
Hardware Revisions - Board: 6.0 CPLD: 4 Dagobah: 225

MAC Address : 00-15-c6-de-ef-ff
IP Address : 192.168.0.69
Netmask : 255.255.255.0
Gateway : 192.168.0.1
TftpServer : 192.168.0.6
Main Memory : 256 MBytes

***** The system will autoboot in 5 seconds *****

Type control-C to prevent autobooting.
. .
Established physical link 100MB Full Duplex
Network layer connectivity may take a few seconds
. . .

******** The system will autoboot now ********

config-register = 0x102
Autobooting using BOOT variable specified file.....

Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.

For help on choosing a boot method, type 'confreg' command.
rommon 1 >

TroyGillian12627 · ‎01-30-2020

thats the thing no one was home during the day I got home and it was back to the other image. I put in the 142 to see if it would boot back to the right image it didn't so I did the bootflash cat again and it came back so now I am going to clear the other image hopefully.

TroyGillian12627 · ‎01-30-2020

Switch#show running-config
Building configuration...

Current configuration : 2227 bytes
!
version 15.0
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
!
hostname Switch
!
boot-start-marker
boot-end-marker
!
!
!
!
no aaa new-model
ip subnet-zero
ip vrf mgmtVrf
!

TroyGillian12627 · ‎01-30-2020

Chassis Type : WS-C4948

Power consumed by backplane : 0 Watts

Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 1000BaseX (SFP) Supervisor WS-C4948 FOX084307L3

M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 0015.c6de.efc0 to 0015.c6de.efef 1.2 12.2(31r)SGA 15.0(2)SG10 Ok

Switch#

TroyGillian12627 · ‎01-30-2020

Switch# show module
Chassis Type : WS-C4948

Power consumed by backplane : 0 Watts

Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 1000BaseX (SFP) Supervisor WS-C4948 FOX084307L3

M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 0015.c6de.efc0 to 0015.c6de.efef 1.2 12.2(31r)SGA 15.0(2)SG10 Ok

Leo Laohoo · ‎01-30-2020

Post the complete output to the following commands:
1. sh version; and
2. dir

TroyGillian12627 · ‎02-01-2020

ok I can not for the life of me get that other image to delete

Leo Laohoo · ‎02-01-2020

delete /f /r bootflash:at4500-ios-promupgrade-122_31r_SGA4

TroyGillian12627 · ‎02-01-2020

ickedsswitch>sh version
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), Version 15.0(2)SG10, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Tue 07-Apr-15 09:46 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x123AE824

ROM: 12.2(31r)SGA4
Dagobah Revision 225, Swamp Revision 4

wickedsswitch uptime is 51 minutes
System returned to ROM by abort at PC 0x0
System image file is "bootflash:cat4500-entservicesk9-mz.150-2.SG10.bin"

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediatel

TroyGillian12627 · ‎02-01-2020

wickedsswitch>ckedsswitch>sh version
^
% Invalid input detected at '^' marker.

wickedsswitch>$-ENTSERVICESK9-M), Version 15.0(2)SG10, RELEASE SOFTWARE (fc1)
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M), ^Version 15.0(2)SG10, RELEASE SOFTWARE (fc1)

% Invalid input detected at '^' marker.

wickedsswitch>Technical Support: http://www.cisco.com/techsupport
^
% Invalid input detected at '^' marker.

wickedsswitch>Copyright (c) 1986-2015 by Cisco Systems, Inc.
^
% Invalid input detected at '^' marker.

wickedsswitch>Compiled Tue 07-Apr-15 09:46 by prod_rel_team
^
% Invalid input detected at '^' marker.

wickedsswitch>Image text-base: 0x10000000, data-base: 0x123AE824
^
% Invalid input detected at '^' marker.

wickedsswitch>
wickedsswitch>ROM: 12.2(31r)SGA4
^
% Invalid input detected at '^' marker.

wickedsswitch>Dagobah Revision 225, Swamp Revision 4
^
% Invalid input detected at '^' marker.

wickedsswitch>
wickedsswitch>wickedsswitch uptime is 51 minutes
^
% Invalid input detected at '^' marker.

wickedsswitch>System returned to ROM by abort at PC 0x0
^
% Invalid input detected at '^' marker.

wickedsswitch>$e file is "bootflash:cat4500-entservicesk9-mz.150-2.SG10.bin"
System image file is "bootflash:cat4500-entservicesk9-mz.150-2.SG10.bin"
^
% Invalid input detected at '^' marker.

wickedsswitch>
wickedsswitch>
wickedsswitch>$t contains cryptographic features and is subject to United
This product contains cryptographic features and is subject to United
^
% Invalid input detected at '^' marker.

wickedsswitch>$local country laws governing import, export, transfer and
States and local country laws governing import, export, transfer and
^
% Invalid input detected at '^' marker.

wickedsswitch>use. Delivery of Cisco cryptographic products does not imply
^
% Invalid input detected at '^' marker.

wickedsswitch>$ authority to import, export, distribute or use encryption.
third-party authority to import, export, distribute or use encryption.
^
% Invalid input detected at '^' marker.

wickedsswitch>$exporters, distributors and users are responsible for
^
% Invalid input detected at '^' marker.

wickedsswitch>$with U.S. and local country laws. By using this product you
compliance with U.S. and local country laws. By using this product you
^
% Invalid input detected at '^' marker.

wickedsswitch>$mply with applicable laws and regulations. If you are unable
agree to comply with applicable laws and regulations. If you are unable
^
% Invalid input detected at '^' marker.

wickedsswitch>$ith U.S. and local laws, return this product immediatel

Leo Laohoo · ‎02-01-2020

Look at your cursor: The symbol is ">" instead of "#".
You won't be able to delete anything if you are not in Enable mode.

TroyGillian12627 · ‎02-01-2020

Directory of bootflash:/

1 -rwx 424748 Nov 19 2014 18:00:29 +00:00 cat4500-ios-promupgrade-122_31r_SGA4
2 -rwx 19476896 Jan 29 2000 11:05:49 +00:00 cat4500-entservicesk9-mz.150-2.SG10.bin
3 -rw- 1202 Jan 1 2000 00:00:04 +00:00 post-2000.01.01.00.00.04-failed.txt
4 -rw- 1202 Jan 1 2000 00:02:38 +00:00 post-2000.01.01.00.02.38-failed.txt
5 -rw- 1202 Jan 1 2000 00:05:12 +00:00 post-2000.01.01.00.05.12-failed.txt
6 -rw- 1202 Jan 1 2000 00:09:16 +00:00 post-2000.01.01.00.09.16-passed.txt
7 -rw- 1202 Jan 1 2000 00:11:50 +00:00 post-2000.01.01.00.11.50-failed.txt

60817408 bytes total (40908848 bytes free)

TroyGillian12627 · ‎02-01-2020

2 -rwx 19476896 Jan 29 2000 11:05:49 +00:00 cat4500-entservicesk9-mz.150-2.SG10.bin
3 -rw- 1202 Jan 1 2000 00:00:04 +00:00 post-2000.01.01.00.00.04-failed.txt
4 -rw- 1202 Jan 1 2000 00:02:38 +00:00 post-2000.01.01.00.02.38-failed.txt
5 -rw- 1202 Jan 1 2000 00:05:12 +00:00 post-2000.01.01.00.05.12-failed.txt
6 -rw- 1202 Jan 1 2000 00:09:16 +00:00 post-2000.01.01.00.09.16-passed.txt
7 -rw- 1202 Jan 1 2000 00:11:50 +00:00 post-2000.01.01.00.11.50-failed.txt
8 -rw- 1202 Jan 1 2000 14:46:35 +00:00 post-2000.01.01.14.46.35-failed.txt
9 -rw- 1202 Jan 1 2000 15:06:58 +00:00 post-2000.01.01.15.06.58-failed.txt
10 -rw- 1202 Jan 1 2000 15:12:42 +00:00 post-2000.01.01.15.12.42-failed.txt

TroyGillian12627 · ‎02-01-2020

ok so I finally got rid of the other image and have no first slot but when it starts up what do all the failed posts mean.

Leo Laohoo · ‎02-01-2020

In Enable mode, use this command: del /f r flash:post*.txt

Leo Laohoo · ‎01-30-2020

That config-register value is wrong.
Plus, delete the ROMMON file "delete /f /r bootflash:cat4500-ios-promupgrade-122_31r_SGA4".