11-25-2013 07:40 AM - edited 03-07-2019 04:46 PM
Hi,
I have a "WS-X6516A-GBIC" on slot 1 and it just failed, we have reseated it and enabled it via cli but it still doesn't work. The only thing that i haven't tried was to insert it on a different slot. I hope you guys can help me.
------------------ show version ------------------
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXI8, RELEASE SOFTWARE (fc2)
ROM: System Bootstrap, Version 12.2(17r)SX5, RELEASE SOFTWARE (fc1)
------------------ show module ------------------
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1002A6VE
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL091387CJ
3 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SAL0738LNC1
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1128U6VM
6 48 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF SAL1531L56S
7 48 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-TX SAL1210J4N2
9 48 48-port 10/100 mb RJ45 WS-X6148-45AF SAL1026SR2W
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0005.7441.fdbc to 0005.7441.fdcb 4.2 7.2(1) 12.2(33)SXI8 PwrDown
2 0013.7f4d.5e50 to 0013.7f4d.5e7f 10.1 7.2(1) 12.2(33)SXI8 Ok
3 000d.bc1e.b864 to 000d.bc1e.b893 1.3 5.4(2) 12.2(33)SXI8 Ok
5 0013.c347.6328 to 0013.c347.632b 5.2 8.5(2) 12.2(33)SXI8 Ok
6 30e4.dbef.3b40 to 30e4.dbef.3b6f 4.1 8.4(1) 12.2(33)SXI8 Ok
7 001e.7afa.ecd0 to 001e.7afa.ecff 1.7 8.4(1) 12.2(33)SXI8 Ok
9 0018.1942.0590 to 0018.1942.05bf 3.1 8.3(1) 12.2(33)SXI8 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
5 Policy Feature Card 3 WS-F6K-PFC3B SAL09391RLS 2.1 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL09391SRB 2.3 Ok
6 IEEE Voice Daughter Card WS-F6K-48-AF SAL1531LGXW 2.5 Ok
9 IEEE Voice Daughter Card WS-F6K-FE48-AF SAL1028UJTP 1.5 Ok
Mod Online Diag Status
---- -------------------
1 Not Applicable
2 Pass
3 Pass
5 Pass
6 Pass
7 Pass
9 Pass
------------------ show power ------------------
system power redundancy mode = redundant
system power total = 2771.16 Watts (65.98 Amps @ 42V)
system power used = 1221.36 Watts (29.08 Amps @ 42V)
system power available = 1549.80 Watts (36.90 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 WS-CAC-3000W 2771.16 65.98 OK OK on
2 WS-CAC-3000W 2771.16 65.98 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 150.36 3.58 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
1 WS-X6516A-GBIC 152.04 3.62 - - on off (Fabric channel errors)
2 WS-X6548-GE-TX 125.16 2.98 125.16 2.98 on on
3 WS-X6148-RJ-45 100.38 2.39 100.38 2.39 on on
5 WS-SUP720-3B 282.24 6.72 282.24 6.72 on on
6 WS-X6148A-GE-45AF 282.24 6.72 282.24 6.72 on on
7 WS-X6148A-GE-TX 105.00 2.50 105.00 2.50 on on
9 WS-X6148-45AF 107.94 2.57 107.94 2.57 on on
Inline Inline Inline Inline
Pwr-Requested Pwr-Allocated Local-Pwr-Pool Power
Slot Card-Type Watts A @42V Watts A @42V Watts A @42V Status
---- ------------------ ------- ------ ------- ------ ------- ------ ----------
6 WS-F6K-48-AF - - - - 34.61 0.82 On
9 WS-F6K-FE48-AF - - - - 34.61 0.82 On
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 1221.36 Watts (29.08 Amps @ 42V)
system auxiliary power used = 0 Watt
Inline Inline-Pwr Inline-Pwr VDB
Pwr-Limit Used-Thru-Pri Used-Thru-Aux Aux-Pwr
Slot Card-Type Watts A @42V Watts A @42V Watts A @42V Capable
---- ------------------ ------- ------ ------- ------ ------- ------ -------
6 WS-F6K-48-AF 850.08 20.24 34.44 0.82 - - No
9 WS-F6K-FE48-AF 840.00 20.00 34.44 0.82 - - No
---- ------------------ ------- ------ ------- ------ ------- ------ -------
Totals: 68.88 1.64 - -
11-25-2013 08:34 AM
Try a different slot ie. slot 4 is available in your chassis. If that works then it is likely to be a problem with the actual chassis itself.
Jon
11-25-2013 12:54 PM
I have a "WS-X6516A-GBIC" on slot 1 and it just failed, we have reseated it and enabled it via cli but it still doesn't work.
To add what Jon has stated, post the "sh log". The diagnostics should reveal a lot of useful information.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide