We are planning on going 10G on some of your ERP system.
We currently have SUP720-3B and I have a few questions about the 10G blades
Here is my show mod output
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL09018L0N
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1315N06M
3 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1549X9DK
4 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1549X9D2
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1316NLEF
6 2 Supervisor Engine 720 (Hot) WS-SUP720-3B SAL16084YG6
7 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1611787Z
8 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1611789C
9 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL16020YBP
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0008.7dce.2248 to 0008.7dce.2277 10.1 7.2(1) 8.7(0.22)BUB Ok
2 0025.4551.6720 to 0025.4551.674f 11.3 7.2(1) 8.7(0.22)BUB Ok
3 70ca.9bf8.93c8 to 70ca.9bf8.93f7 11.5 7.2(1) 8.7(0.22)BUB Ok
4 70ca.9bf8.8a98 to 70ca.9bf8.8ac7 11.5 7.2(1) 8.7(0.22)BUB Ok
5 001f.6c77.2194 to 001f.6c77.2197 5.8 8.5(3) 12.2(33)SXH8 Ok
6 5475.d07b.a108 to 5475.d07b.a10b 5.13 8.5(4) 12.2(33)SXH8 Ok
7 442b.0381.b828 to 442b.0381.b857 4.2 12.2(18r)S1 12.2(33)SXH8 Ok
8 442b.0381.b190 to 442b.0381.b1bf 4.2 12.2(18r)S1 12.2(33)SXH8 Ok
9 70ca.9b68.ebfc to 70ca.9b68.ec2b 4.2 12.2(18r)S1 12.2(33)SXH8 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
5 Policy Feature Card 3 WS-F6K-PFC3B SAL1316NKH6 2.5 Ok
5 MSFC3 Daughterboard WS-SUP720 SAL1316NN4Q 3.3 Ok
6 Policy Feature Card 3 WS-F6K-PFC3B SAL160850W2 2.6 Ok
6 MSFC3 Daughterboard WS-SUP720 SAL16084YQK 5.1 Ok
7 Centralized Forwarding Card WS-F6700-CFC SAL1611704A 4.1 Ok
8 Centralized Forwarding Card WS-F6700-CFC SAL16138HQL 4.1 Ok
9 Centralized Forwarding Card WS-F6700-CFC SAL16031753 4.1 Ok
Now here my question
Does anymore see any issue with going to 10G blades with our current SUP.
also I am abit worried that the buffer 90MB per port group maybe too low
What is a port in these 10G blades are we talking ports 1 to 8 as group
Please any insight will be welcomed
