Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Resolved! Netflow 9 not working.
We have installed "FRULink 10G SM Module" in our 3560X switch and have configured Netflow 9.But we are not getting the flows to the netflow server, except 1 or 2 multicast packets.IOS:c3560e-universalk9-mz.150-1.SE3.bin (IP SERVICES)Configuration:flo...
Hi allI was told the other day that there is an option in dhcp server i think its 43, where is gives the ip phone the correct ip address for the vlan, is this correct ?also how does the switch know that the phone is a tagged packet, does the 802.1p t...
Hello,when i make a traceroute on an ASR 1001 router to 172.23.30.7 I get the following output:VRF info: (vrf in name/id, vrf out name/id) 1 192.168.99.192 0 msec 192.168.99.191 1 msec 192.168.99.192 0 msec 2 172.23.30.243 1 msec 1 msec 1 mse...
Hi all,We have an issue with limited multicast traffic allowed on our provider network (metro ethernet). So currently our OSPF adjacencies time out from time to time. Remembering that the neighbor command changes EIGRP communication to a neighbor fro...
Resolved! 2 default-gateways and 1 EIGRP process
I was wondering if someone could offer advice on how I should setup my EIGRP routing process. I have a simple network of R0---R1---R2---R3. Currently R2 has a static 0.0.0.0 default route to R3 to the Internet. R2 has an EIGRP process setup with R0 a...
I have a 5915 mobile router with software version 15.2(1r)GC1. Ports FE0/0 and FE0/1 are routed ports. Ports FE0/2 through FE0/4 are layer 2 switched ports. I'd like to put FE0/1 and FE0/2-4 in the same address space so that all four ports can be use...
I am having a problem with CIsco routers 1841. They are new and when i started configuring them this is what happened. I coppied the and pasted the configs and they stuck as per the picture below. Please assist what might be th epr...
Hi Folks,I'm having some issues with multicast routing - though it certainly wouldn't be my strongest area of networking expertise so it may be something simple. I have two sources for group 239.192.255.3 on two VLANs (43, 10.4.43.28 and 943, 192.16...
I am trying to have my routers joing multiple group using the igmp join-group command. It only works for one group.I tried ip igmp join-group 224.1.2.1 100but it rejects the command
plz suggest In what scenerio we use BFD either direct or indirect connectivity from router side?
I cannot seem to find any document on replacing the faulty Active member of VSS pair, please help.
Devices are 3750-24TS Switches, software version is 12.2(55)SE6.I need some more advices about how to troubleshoot this issue, I have a pair of ports which are not bundling, no matter what. Is the same behavior with LACP or PAgP. In this outputs I ha...
Hi,In 3750 switch,I have configured intervlan routing.I have three vlans Vlan 10,vlan 20,Vlan 30 and I have assigned IP address for that Vlan.In vlan 10,I have connected one systen gigabitethernet 0/1 interface.From my system I am able to ping vlan 1...
Topology of AS 10:R1------------------------R4 (RR)| |R2 (RR)-----------------R5 R1 advertises BGP route 168.1.0.0 to R2 and R4. R5 learns IBGP route 168.1.0.0 from RR R2 and RR R4. The route reflected by R2 is the b...
hi,In HSRP configuration how many switches(Maximum) are participated in this.Kindly tell multicast mac address for HSRP.Regards,kabeer.s
