Tag: "port_issues" in "Networking Knowledge Base"

Buy or Renew

Latest Tagged

Unable to connect Catalyst switch to the Ether Switch Module on a router that uses the straight thro... - ( ‎06-22-2009 03:42 PM )

by on

0 Comments 826 Views

0 Comments

826 Views

Port status is errdisable due to BPDU guard - ( ‎06-22-2009 04:02 PM )

by on

0 Comments 225588 Views

0 Comments

225588 Views

How to prevent the input queue drops and output queue drops in Catalyst switches running Cisco IOS s... - ( ‎06-22-2009 04:05 PM )

by on

0 Comments 6113 Views

0 Comments

6113 Views

The user is unable to assign an IP address to a Layer 3 (L3) sub-interface on a Catalyst 3750 or 355... - ( ‎06-22-2009 04:06 PM )

by on

0 Comments 3531 Views

0 Comments

3531 Views

The %SYS-4-SYS_LCPERR4:Module [dec]: LTL Parity error detected on Coil #[dec] error message appears... - ( ‎06-22-2009 04:06 PM )

by on

0 Comments 3633 Views

0 Comments

3633 Views

Input errors on the Layer-3 interface of Catalyst 6500 switch running Cisco IOS when connected to th... - ( ‎07-01-2009 04:57 AM )

by on

0 Comments 2942 Views

0 Comments

2942 Views

How to configure the Gigabit Ethernet fiber-optic interface to support duplex speed in Cisco Catalys... - ( ‎06-22-2009 04:11 PM )

by on

0 Comments 10667 Views

0 Comments

10667 Views

A VLAN might disappear due to a duplex mismatch, which causes connectivity issues - ( ‎06-22-2009 04:12 PM )

by on

0 Comments 747 Views

0 Comments

747 Views

The %PM_SCP-SP-3-LCP_FW_ABLC: Late collision message from module error message appears in Catalyst ... - ( ‎06-22-2009 04:38 PM )

by on Latest post on by

1 Comments 11060 Views

1 Comments

11060 Views

Recovering from ErrDisabled port due to misconfiguration - ( ‎06-22-2009 04:39 PM )

by on Latest post on by

2 Comments 246929 Views

2 Comments

246929 Views

Top Tagged

When port security is enabled, MAC addresses are detected but after a short while the port is shut d... - ( ‎06-22-2009 06:12 PM )

by on

0 Comments 1383 Views

0 Comments

1383 Views

The "%DOT1X_SWITCH-5-ERR_ADDING_ADDRESS:" error message appears in Cisco Catalyst 3550 or 3750 serie... - ( ‎06-22-2009 06:07 PM )

by on Latest post on by

2 Comments 8787 Views

2 Comments

8787 Views

How to run GOLD diagnostic tests on Catalyst 6500/6000 series switches to troubleshoot hardware issu... - ( ‎06-22-2009 05:38 PM )

by on

0 Comments 18797 Views

0 Comments

18797 Views

How to configure the errdisable flap-setting values in Cisco Catalyst switches running Cisco IOS sys... - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Comments 14880 Views

2 Comments

14880 Views

User cannot get a Gigabit Ethernet link up between a Cisco switch and a non-Cisco device due to auto... - ( ‎06-22-2009 03:40 PM )

by on

0 Comments 1480 Views

0 Comments

1480 Views

The %RTD-1-LINK_FLAP [chars] link down/up [dec] times per min error message appears on a port - ( ‎06-22-2009 03:40 PM )

by on

0 Comments 4004 Views

0 Comments

4004 Views

Runts and CRC errors increment in the show interface command output on a Cisco IOS-based switch, or ... - ( ‎06-22-2009 03:40 PM )

by on

0 Comments 79082 Views

0 Comments

79082 Views

A SPAN destination port is shown as "not connected" and does not communicate with the rest of the ne... - ( ‎06-22-2009 05:35 PM )

by on

0 Comments 8573 Views

0 Comments

8573 Views

The "%C4K_HWPORTMAN-4-BLOCKEDTXQUEUE" error message on Cisco Catalyst 4500 series switches connected... - ( ‎06-22-2009 05:34 PM )

by on Latest post on by

2 Comments 22731 Views

2 Comments

22731 Views

When redundancy is run, unable to use all eight ports on both of the Supervisor 5 engines in a Catal... - ( ‎06-22-2009 05:33 PM )

by on

0 Comments 1230 Views

0 Comments

1230 Views

Top Taggers

User

Count