04-23-2003 10:21 AM - edited 03-17-2019 08:01 PM
I have a 5350 router, and I get some troubles. I can't use fax over wan links. Before I had a 5300 router and it works fine (same IOS version). Voice works fine, but I can't use fax. This interface is E1 with ISDN Q-Sig.
Configuration below...
==
version 12.2
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
!
hostname 5350
!
no boot startup-test
logging buffered 20480 debugging
aaa new-model
!
!
aaa authentication login default local
aaa authentication enable default enable
aaa session-id common
!
!
resource-pool disable
calltracker enable
spe default-firmware spe-firmware-1
!
!
!
!
ip subnet-zero
ip cef
!
frame-relay switching
isdn switch-type primary-qsig
isdn voice-call-failure 0
!
voice call send-alert
voice call carrier capacity active
voice rtp send-recv
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0
!
!
!
mta receive maximum-recipients 0
!
!
controller E1 3/0
pri-group timeslots 1-31
!
interface FastEthernet0/0
ip address x.x.x.x x.x.x.x
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
!
interface Serial3/0:15
no ip address
isdn switch-type primary-qsig
isdn overlap-receiving
isdn incoming-voice modem
isdn bchan-number-order ascending
isdn sending-complete
no cdp enable
!
interface Group-Async0
ip unnumbered FastEthernet0/0
encapsulation ppp
ip tcp header-compression
async mode dedicated
peer default ip address pool mypool
ppp authentication pap
group-range 1/00 1/59
!
ip local pool mypool x.x.x.x x.x.x.x
ip classless
ip route 0.0.0.0 0.0.0.0 x.x.x.x
no ip http server
!
!
call rsvp-sync
!
voice-port 3/0:D
bearer-cap Speech
!
voice-port 3/1:0
compand-type a-law
!
!
mgcp profile default
!
dial-peer cor custom
!
!
!
dial-peer voice 8400 pots
application data_dialpeer
incoming called-number 8400
port 3/1:0
forward-digits all
!
dial-peer voice 1000 pots
destination-pattern 1...
direct-inward-dial
port 3/0:D
forward-digits all
!
dial-peer voice 1001 pots
destination-pattern 8...
direct-inward-dial
port 3/0:D
forward-digits all
!
dial-peer voice 2000 voip
destination-pattern 12..
session target ipv4:x.x.x.x
dtmf-relay rtp-nte
ip qos dscp cs5 media
!
5350#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 5350 Software (C5350-IS-M), Version 12.2(11)T8, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 27-Mar-03 22:32 by hqluong
Image text-base: 0x60008948, data-base: 0x61380000
ROM: System Bootstrap, Version 12.2(1r)1, RELEASE SOFTWARE (fc1)
BOOTLDR: 5350 Software (C5350-BOOT-M), Experimental Version 12.1(20000922:142008) [nag-flo_t_0110 101]
cfw-5350-voip uptime is 1 day, 3 hours, 8 minutes
System returned to ROM by reload at 00:23:01 brz Fri Jan 21 2000
System image file is "flash:c5350-is-mz.122-11.T8.bin"
cisco AS5350 (R7K) processor (revision T) with 131072K/65536K bytes of memory.
Processor board ID JAE070401D5
R7000 CPU at 250Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
Last reset from IOS reload
Channelized E1, Version 1.0.
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
Primary Rate ISDN software, Version 1.1.
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x32,
Board Hardware Version 3.34, Item Number 800-5171-02,
Board Revision C0, Serial Number JAE070401D5,
PLD/ISP Version 2.2, Manufacture Date 24-Jan-2003.
Processor 0x14, MAC Address 0x0B5FDAB22
Backplane HW Revision 1.0, Flash Type 5V
2 FastEthernet/IEEE 802.3 interface(s)
37 Serial network interface(s)
60 terminal line(s)
2 Channelized E1/PRI port(s)
512K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
8192K bytes of processor board Boot flash (Read/Write)
Configuration register is 0x2102
5350#
===
Can someone help me?
regards
04-23-2003 07:44 PM
Need to know what exact problem you have for fax calls. Here is the link which has config and step by step troubleshooting for fax calls.
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_access/fxmdmnt.htm
04-28-2003 12:15 PM
I make the voice call, and when I try to establish the fax, the sending side machine cannot not "pull" the paper, and the receiving side appears like receiving but nothing happens.
I've tried somethig from this document, but I can't see changes.
07-31-2004 02:03 AM
try this:
voice service pots
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711alaw
dial-peer voice 900 voip
permission term
description your outgoing dialpeer
destination-pattern ^1234..
modem relay nse codec g711alaw redundancy
modem relay latency 150
modem relay sprt retries 6
fax-relay ecm disable
fax nsf 000000
fax protocol t38 ls-redundancy 2 hs-redundancy 2 fallback pass-through g711ulaw
no vad
and make sure you have g711alaw and g711ulaw in your codec preference list.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide