Hello Paulo ,
Given below is what i see on the CLI
*****************************************************************************************************************************************************************
se-10-1-1-10> reload
Are you sure you want to reload?
Doing a reload will cause any unsaved configuration data to be lost.
Continue[y]? : y
se-10-1-1-10>
MONITOR SHUTDOWN...
EXITED: ${ROOT}/bin/probe exit status 0
EXITED: SQL_startup.sh exit status 0
EXITED: LDAP_startup.sh exit status 0
EXITED: HTTP_startup.sh exit status 0
MONITOR EXIT...
INIT: Remounting device 03:01 ... OK
Done.
Restarting system.
Initializing memory. Please wait. 256 MB SDRAM detected
BIOS Version: SM 02.00
BIOS Build date: 09/17/02
System Now Booting ...
Booting from flash..., please wait.
[BOOT-ASM]
7Found Intel 82371AB at 0x00000000 ROM address 0x00000000
Please enter '***' to change boot configuration: ***Probing...[EEPRO100]Found I // I DO THIS AND GO INTO THE BOOT-LOADER
ntel EtherExpressPro100 at 0x00000000 ROM address 0x00000000
Found Intel EtherExpressPro100 at 0x00000000 ROM address 0x00000000
Ethernet addr: 00:14:1C:95:FC:A2
equalizer val: 16
ServicesEngine Bootloader Version : 1.0.17
ServicesEngine boot-loader> boot helper // THEN I TYPE "boot helper"
Probing...[EEPRO100]Found Intel EtherExpressPro100 at 0x00000000 ROM address 0x
00000000
Found Intel EtherExpressPro100 at 0x00000000 ROM address 0x00000000
Ethernet addr: 00:14:1C:95:FC:A2
equalizer val: 16
Me: 10.1.1.10, Server: 10.1.1.55, Gateway: 10.1.1.11
Loading cue-installer.2.3.1 //AFTER THIS STEP CUE RELOADS IT SELF
-
Initializing memory. Please wait. 256 MB SDRAM detected
BIOS Version: SM 02.00
BIOS Build date: 09/17/02
System Now Booting ...
Booting from flash..., please wait.
[BOOT-ASM]
7Found Intel 82371AB at 0x00000000 ROM address 0x00000000
Please enter '***' to change boot configuration: Filesystem type is reiserfs,
partition type 0x83
kf: a1 : (hd0,0)/bzImage root=/dev/hda1 ro plat=nm
kf: a2 : (hd0,0)/bzImage root=/dev/hda1 ro plat=nm
in grub_open: (hd0,0)/bzImage root=/dev/hda1 ro plat=nm
in grub_open1: /bzImage root=/dev/hda1 ro plat=nm
in grub_open2: /bzImage root=/dev/hda1 ro plat=nm
in grub_open3: /bzImage root=/dev/hda1 ro plat=nm 1
in grub_open: (hd0,0)/bzImage root=/dev/hda1 ro plat=nm
in grub_open1: /bzImage root=/dev/hda1 ro plat=nm
in grub_open2: /bzImage root=/dev/hda1 ro plat=nm
in grub_open3: /bzImage root=/dev/hda1 ro plat=nm 1
In verify_kernel_sig
Chksum: final image size: 809372
plat: 1
Debug: bl_sz: 115296
After: buf_len: 2048
After KEY_InitMem
reading key: 0
reading key: 1
reading key: 2
reading key: 3
reading key: 4
reading key: 5
After karr
After 2: buf_len: 2048
sig len : 172
in verifysignature_md5, MD5 hash generated now, str format:hexmd5:bfb41f99bd669
c4df612cb94f2e81764
Verifying signature now...
calling RSA decrypt now
mem ptr: 0 704 832 968 1040 1172 1184 1196 1208 1220 1228 1244 1268 1284 1300 1
316 1332 1344 1360 1384 1400 1664 1804 2080 2224 2364 2880 3396 3660 3924 4188
RSA decrypt returned:33
verifysignature_md5, Orig MD5 hash generated during encryption:bfb41f99bd669c4d
f612cb94f2e81764
Kernel signature verified successfully
In load_imagea1
In load_imagea2
Dbg ********* filemax/data_len/SECSIZ: 809372/2560/512
[Linux-bzImage, setup=0xa00, size=0xc4d9c]
kernel_func: kt: 3
in boot func: kt: 3
Linux version 2.4.18 (bld_adm@bld-system) (gcc version 2.95.3 20010315 (release)
) #5 Sun Sep 19 22:25:25 PDT 2004
Platform: nm
setup.c: handling flash window at [15MB..16MB]
setup.c: handling kernel log buf at [245.5MB]
setup.c: handling trace buf at [246MB]
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0800 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000000f00000 (usable)
BIOS-e820: 0000000000f00000 - 0000000001000000 (reserved)
BIOS-e820: 0000000001000000 - 000000000f580000 (usable)
BIOS-e820: 000000000f580000 - 000000000f600000 (reserved)
BIOS-e820: 000000000f600000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
On node 0 totalpages: 62848
zone(0): 4096 pages.
zone(1): 58752 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hda1 ro plat=nm
Initializing CPU#0
Detected 498.673 MHz processor.
In serial_console_setup
Calibrating delay loop... 996.14 BogoMIPS
Memory: 244056k/251392k available (1027k kernel code, 5924k reserved, 661k data,
84k init, 0k highmem)
kdb version 2.3 by Scott Lurndal, Keith Owens. Copyright SGI, All Rights Reserve
d
in atrace_init
log_head: h: 0, t: 5717961, l: 0, w: 0, s: 10484672
Using existing trace log
log_head: h: 0, t: 5717961, l: 0, w: 0, s: 10484672
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xeab9c, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Limiting direct PCI/PCI transfers.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: devfs_debug: 0x0
devfs: boot_options: 0x1
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI en
abled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Cisco ContentEngine Flash Driver Version 0.02
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
hda: C/H/S=50127/232/176 from BIOS ignored
hdb: C/H/S=0/0/0 from BIOS ignored
hda: IC25N020ATMR04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 39070080 sectors (20004 MB) w/1740KiB Cache, CHS=38760/16/63, UDMA(33)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1
device capacity not supported
Flash capacity == 39070080
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.
html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@sa
w.sw.com.sg> and others
eth0: PCI device 8086:1229, 00:14:1C:95:FC:A1, IRQ 9.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 668081-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
eth1: PCI device 8086:1229, 00:14:1C:95:FC:A2, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 668081-002, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
IEEE 802.2 LLC for Linux 2.1 (c) 1996 Tim Alpaerts
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
reiserfs: checking transaction log (device 03:01) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Mounted devfs on /dev
Init drive control
Freeing unused kernel memory: 84k freed
INIT: version 2.84 booting
Started device management daemon v1.3.25 for /dev
reiser root fs ...
Reiserfs super block in block 16 on 0x301 of format 3.6 with standard journal
Blocks (total/free): 4883752/4804594 by 4096 bytes
Filesystem is cleanly umounted
Filesystem seems mounted read-only. Skipping journal replay.
Checking internal tree..finished
FILESYSTEM CLEAN
Remounting the root filesystem read-write...
kernel.sem = 16384 32000 32 128
Welcome to Cisco Service Engine
Sun Aug 14 21:49:14 PDT 2005
WARNING: Found files describing previous failures...
Saving them in /var/cores.prev
********** rc.aesop ****************
WARNING: Found files describing previous failures...
Saving them in /var/javacores
==> eth1 exists, we must be running on a Network Module
==> eth1 exists, we must be running on a Network Module
Router communications servers initializing...complete.
IOS IP Address Registration complete.
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.1.1.0 * 255.255.255.0 U 40 0 0 eth1
127.0.0.0 * 255.0.0.0 U 40 0 0 lo
default 142.1.66.254 0.0.0.0 UG 40 0 0 eth1
Reading Manifest...done.
Reading License ...done.
ModuleType = nm
INIT: Entering runlevel: 2
********** rc.post_install ****************
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
STARTED: cli_server.sh
STARTED: ntp_startup.sh
STARTED: LDAP_startup.sh
STARTED: superthread_startup.sh
STARTED: SQL_startup.sh
STARTED: HTTP_startup.sh
STARTED: ${ROOT}/usr/wfavvid/run
STARTED: ${ROOT}/bin/probe
waiting 132 ...
SYSTEM ONLINE
se-10-1-1-10>
According to the document when the CUE reloads it should give me the option to install the software or reload ?
Am i doing the right way ??
Regards,
Hasan Jafi
