06-25-2004 05:36 AM - edited 03-18-2019 03:12 PM
After upgrading my Unity server from 4.02 to 4.04 I'm getting tons of compliants from my users about people not being able to leave them voice messages. The Unity server cuts them off. My event log is full of the following errors;
Event Type: Information
Event Source: CiscoUnity_Miu
Event Category: Information
Event ID: 634
Date: 6/25/2004
Time: 7:36:08 AM
User: N/A
Computer: NSIUNITY1
Description:
[Port 4] Recording stopped due to leading silence time out.
For more information, click: http://www.CiscoUnitySupport.com/find.php
I've tried adjusting the recording settings in the system configuration put it didn't make a difference. Any one seen this before?
06-30-2004 07:33 AM
This event warning was introduced in 4.0(4) and is reported when a recording session detects 5 seconds of leading silence, for instance Unity plays the record beep but detects nothing but silence. The recording is stopped and no message is saved. The event warning and your report of Unity cutting people off may or may not be related. If it is related, the question is why would Unity be getting silence during the recording session.
Is it reproducible and/or is it possible to pinpoint the issue to a single path, e.g. a gateway? I think well need to turn on diagnostics to get to the root cause of this issue. If you think the issue is due to the 4.04 upgrade, you may want to open a TAC case to pursue.
04-13-2005 09:14 AM
Hi,
I'm facing the same problem, but I did not upgrade, it is a fresh installation of 4.0(4).
Some users are not able to record messages. The unity is cutting people off.
If open a TAC case, but till today no solution,
Thanks in advance for your help if you can provide it
Kind Regards
MPaiva
04-13-2005 09:14 AM
Hi,
I'm facing the same problem, but I did not upgrade, it is a fresh installation of 4.0(4).
Some users are not able to record messages. The unity is cutting people off.
If open a TAC case, but till today no solution,
Thanks in advance for your help if you can provide it
Kind Regards
MPaiva
04-20-2005 07:48 AM
anybody....get an answere to this...having a real hard time with after 30 seconds unity plays the greeting sorry your maximum recording time has been reached......
05-17-2005 09:39 AM
Did anyone get an answer for this? I am running into this same issue. Except i get a fast busy when the recirding ends. The user gets a 30 second or so message.
Event Type: Information
Event Source: CiscoUnity_Miu
Event Category: Information
Event ID: 626
Date: 5/17/2005
Time: 9:23:29 AM
User: N/A
Computer: SR60-UNITY01
Description:
[Port 1] Recording (0 ms) was less than minimum record length (1000 ms).
For more information, click: http://www.CiscoUnitySupport.com/find.php
06-08-2005 06:24 AM
my issue was it was not licensed for full recording for some reason. Cisco sent me a new license and I was good to go...
06-07-2005 02:44 PM
If the Unity Server has two NICs installed, verify that only one NIC is enabled. If both NICs are enabled, a binding issue could occur and audio cut through will fail from the calling party to the Unity voice mail box.
07-05-2005 05:15 AM
Is Cisco had comfirm that solution ?
We having the same problems on IBM x255 dual NIC configured in Fault Tolerance mode.
If someone tryied to upgrade the NIC Drivers ?
Martin
02-15-2006 11:56 AM
If you are using MGCP and users are getting cut off leaving voicemail try the following command:
no mgcp timer receive-rtcp
03-02-2006 05:54 AM
You helped me a lot here! I've been troubleshooting a license upgrade and did not find a solution to the OPs issue until I found your post. High Five!
Regards
/David
04-17-2006 05:15 PM
I had a Unity 4.0(5) go down hard and we brought it back online fine, but audio recording was not working. Turns out the HP teaming broke and never came back. So one NIC had DHCP and the other had the static address it was assigned. Rebuild the Team and reboot.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide