My customer is running 4x C880A M8 cluster, but keep experiencing RAID 1 volume degrade issue whenever OS is booting. (changed to rebuilding status)I've tried rebooting with different type of M.2 SSD (Micron coming from Cisco, Intel Solidigm, and Del...
Forum Posts
Cisco UCS 240 M8 Server - CIMC configured but not working facing the same issue in five servers. Connected peer to peer still same issue so did factory reset ping came for few seconds then again, it was not working. Does anyone face this kind of issu...
Body: Hello everyone,I'm seeking some advice regarding an issue with a Cisco UCS C240 M5SX server. On September 17, 2026, the server triggered an unexpected hard reset.Here are the details from the System Event Log (CIMC):Event: BMC WATCHDOG (Watchdo...
Hello.I have Cisco UCS 5108 Cisco UCS B200 M3 (BIOS B200M3.2.2.6h, Board Controller 3.2(3p)B, CIMC Controller 3.2(3p)B, FlexFlash Controller 1.2 build 258-1)After changing the profile, the server stopped loading. Errors in SEL LOGS:69e | 09/23/2026 ...
Hi all,I have two standalone C-series servers (UCS220 M7) with a VIC 15237 MLOM (100G, QSFP-100G-LR-S) connected directly to IOS-XR routers.The vNIC is in Trunk mode with no default VLAN, VNTAG mode is disabled, and Physical NIC Mode is on so that Li...
Greetings to all,Do existing UCS-FI-6454 which were part of Cisco UCS server blades forming SPLUNK support direct connectivity to the HPE serversSwitches:2 × Cisco UCS Fabric Interconnect 6454 (UCS-FI-6454)Servers:7 × HPE ProLiant DL340e Gen12 (Index...
I'm in the middle of upgrading a pair of FIs and after the first one rebooted, it came back up with an uplink port down. I'm curious if it's safe to reset the uplink port before proceeding to the second FI or should I proceed with the second FI's up...
UCS won't boot. Tried booting using USB Drive, vKVM and finally attached an external CD-ROM. Attached are some of the error messages. Most informational message is when I tried installing CML from a DVD-ROM Drive.
Im looking for a visio stencil for the UCS FI-6664 to be posted. Does anyone have that front and rear stencil they can share or know who to contact to update the UCS stencil zip that looks to be last updated in 2025?Thank you,Todd
Hello,I need to change management networks and IP addresses that I'm using to access UCS-M and my blades.For UCS-M is it as simple as changing Management Interfaces on the Admin tab or do I need change IP addresses on each FI via CLI?Also, I'm using ...
Hi.I am working on an upcoming UCS FI 6200 to 64108 migration running infrastructure firmware 4.1(3m).Regarding the existing ports, this UCS domain is using direct-attached iSCSI storage using appliance ports. Are there any additional steps that need...
Hi I would like to know if the UCS B200 M5 blade server is UL 60950-1 compliant
Hello I am looking for the MTBF for the UCS B200 M5 blade server.
Hello All,I have a C220 M6N that will not power on. It appears the Intel ME Node Manager is "unhealthy or unresponsive" per the log and it's causing the server to not power on. I also have a corrupted BIOS, see logs below.Critical F1707 sys/rack-unit...
Hoping someone here has walked this exact path. I have a **UCS-E140DP-M1/K9** blade that I bought second-hand — no service contract, and the module is**past its Last Day of Support (2021-05-31)**. The x86 host side is completely fine; Windowsboots an...
