About Marco Soeder-Schuettler

Marco Soeder-Schuettler · 10-31-2025

Hi all, in need some help, hope i can explain my problem correctly.Our company uses a third party contact center solution and we have different call center extensions for each departement.The SIP Trunk connection works fine between Callmanager and co...

Marco Soeder-Schuettler · 11-22-2016

Hi all, hope somone can help and explain me the following configuration situation. In an existing network are multiple ESX Server. All ESX Server have the same network configuration. VMNIC3 on Switchport 1/0/33VMNIC4 on Switchport 1/0/29VMNIC5 on Swi...

Marco Soeder-Schuettler · 10-10-2016

Hi all, ich have two Access Switches - WS-C2960S-48TS-L 12.2(55)SE10, since some days i see high CPU. These ar the Log entries:.Oct 10 09:22:04.366: IP ARP: rcvd req src 172.18.12.214 9890.9699.5401, dst 172.18.1.50 Vlan1.Oct 10 09:22:04.366: IP ARP:...

Marco Soeder-Schuettler · 09-13-2016

Hi all, i have two Catalyst 3750X-12S Switche, they are connected together on 1G single Trunk. Now i want to create an Etherchannel Trunk on two or more Ports for more data throughput.. Is there any way to setup Etherchannel Trunk without loss of l...

Marco Soeder-Schuettler · 09-12-2016

Hey guys, i have a question more about designing a VLAN network. Our customer has a /16 network with roundabout 1500 devices and 90 Cisco switches. All devices are in VLAN 1 in subnet 192.168.0.0/16. Now its my part to Re-Design this network in diffe...

Marco Soeder-Schuettler · 10-10-2016

Thanks to all, the Problem is solved. Somone activates "debug ip arp", since no deb all cpu is normal again. Regards Marco

Marco Soeder-Schuettler · 10-10-2016

Hi, here the show run output SW-RZ1-2960S-018#sh runBuilding configuration... Current configuration : 6572 bytes!! Last configuration change at 07:08:16 UTC Mon Oct 10 2016 by cisco! NVRAM config last updated at 13:57:14 UTC Fri Oct 7 2016 by cisco!...

Marco Soeder-Schuettler · 10-10-2016

Hi Leo, SW-RZ1-2960S-018#sh proc cpu sort | ex 0.00CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 10 1472311814 323935027 4545 87.79% 85.60% 85.52% 0 ARP Input 140...

Marco Soeder-Schuettler · 09-12-2016

Yes, so you can do ;-) Make sure that active / passive negotiation is already done.

Marco Soeder-Schuettler · 09-12-2016

Hi, in case of reboot a standby Unit i disconnect all interface cables and connect only failover interface cable. Then wait for negotiate failover active and passive then connect all other cables again In this case there is no risk that both units b...

Member Since	‎01-25-2016 01:17 PM
Date Last Visited	‎11-12-2025 07:28 AM
Posts	20
Total Helpful Votes Received	2

User Statistics

User Activity

Route Pattern to Route certain extensions into an XCAPI SIP Trunk

Switchport config and ESX - Etherchannel

Cisco Switch high CPU - ARP Input

Create Etherchannel Uplink

Re-Design Network with InterVLAN Routing

Thanks to all, the Problem is

Hi, here the show run output

Hi Leo,

Yes, so you can do ;-)

Hi,